Bedienungsanleitung Hikoki D13 (Seite 4 von 100) (Alle Sprachen)

816291

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

Lock

Switch locks to the “ON” position.

Disconnect mains plug from electrical outlet

Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed in the below.

○ Chuck wrench ........................................................... 1

○ Side handle ............................................................... 1

Standard accessories are subject to change without notice.

APPLICATIONS

Drilling in metal, lumber and plastics.

SPECIFICATIONS

Voltage*1(110 V, 115 V, 120 V, 127 V,

220 V, 230 V, 240 V)

Power input*1720 W

No load speed 650 min-1 (Except for EU

countries: 550 min-1)

Capacity Steel 13 mm

Wood 40 mm

Weight (without cord)*23.1 kg

*1 Be sure to check the nameplate on product as it is

subject to change by areas.

*2 According to EPTA-Procedure 01/2014

NOTE

Due to HiKOKI’s continuing program of research and

development speciﬁ cations herein are subject to change

without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Fixing spade handle 1 90

Fixing side handle 2 90

Mounting and dismounting the bit 3 90

Selecting rotational direction 4 91

Switch operation 5 91

Locking-on the switch 6 91

Rereasing the switch 7 91

Fixing handle joint 8 91

Fixing depth stopper 9 92

Replacing carbon brushes 10 92

Selecting accessories ―93

Selecting the appropriate drill bit:

○ When boring metal or plastic

Use ordinary metalworking drill bits.

Sizes range from a minimum of 1.2 mm to chuck

maximum capacity.

○ When boring wood

Use ordinary woodworking drill bits.

However, when drilling 6.5 mm or smaller holes, use a

metalworking drill bit.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of an abraded drill bits will cause motor

malfunctioning and degraded eﬃ ciency, replace the drill

bits with a new one or resharpening without delay when

abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Inspecting the carbon brushes

The motor employs carbon brushes which are

consumable parts.

When the brushes are worn down, motor trouble may

result. When the brushes are worn down to the limit

line ⓐ, replace the brushes with new ones. Keep the

brushes clean, so that they smoothly slide into the brush

holders.

When replacing the brushes with new ones, be sure to

use a pair of brushes for HiKOKI ELECTRIC DRILL Type

D13 corresponding to the illustrated number ⓑ. Auto-

stop carbon brushes automatically cut oﬀ the electric

circuit, when it is worn down to the wear limit.

This indicates the replacement time of the brush and

prevents damage of the commutator.

4. Replacing carbon brushes

Disassemble the brush caps with a slotted-head

screwdriver. The carbon brushes can then be easily

removed.

5. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI power tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the power tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

000BookD13.indb4000BookD13.indb4 2022/12/2712:26:462022/12/2712:26:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki D13 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info