Bedienungsanleitung Hikoki M12V2 (Seite 7 von 128) (Alle Sprachen)

816316

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

English

SPECIFICATIONS

Model M12V2

Voltage (by areas)* (110 V, 230 V)

Power Input* 2000 W

Collet Chuck Capacity 12 mm or 1/2"

No-load speed 8000–22000 min-1

Main Body Stroke 65 mm

Weight (without cord and

standard accessories) 6.9 kg

* Be sure to check the nameplate on product as it is subject

to change by areas.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If the

plug is connected to a receptacle while the power switch

is in the ON position, the power tool will start operating

immediately, which could cause a serious accident.

3. Extension cord

When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

4. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

INSTALLING AND REMOVING BITS

WARNING

Be sure to switch power OFF and disconnect the plug

from the receptacle to avoid serious trouble.

1. Installing bits

(1) Clean and insert shank of bit into the collet chuck until

shank bottoms, then back it out approximately 2 mm.

(2) With the bit inserted and pressing the lock pin holding

the armature shaft, use the 23 mm wrench to ﬁ rmly

tighten the collet chunk in a clockwise direction (viewed

from under the router). (Fig. 1)

CAUTION

○ Ensure that the collet chuck is ﬁ rmly tightened after

inserting a bit. Failure to do so will result in damage to

the collet chuck.

○ Ensure that the lock pin is not inserted into the armature

shaft after tightening the collet chuck. Failure to do so

will result in damage to the collet chuck, lock pin and

armature shaft.

(3) When using the 8 mm diameter shank bit, replace the

equipped collet chuck with the one for 8 mm diameter

shank bit which is provided as the standard accessory.

2. Removing Bits

When removing the bits, do so by following the steps for

installing bits in reverse order. (Fig. 2)

CAUTION

Ensure that the lock pin is not inserted into the armature

shaft after tightening the collet chuck. Failure to do so

will result in damage to the collet chuck, lock pin and

armature shaft.

HOW TO USE THE ROUTER

1. Adjusting depth of cut (Fig. 3)

(1) Place the tool on a ﬂ at wood surface.

(2) Turn the quick adjustment lever in a counterclockwise

direction until the quick adjustment lever stops. (Fig. 4)

(3) Turn the stopper block so that section to which the cutting

depth setting screw on a stopper block is not attached

comes to the bottom of the stopper pole. Loosen pole

lock knob allowing the stopper pole to contact with

stopper block.

(4) Loosen the lock lever and press the tool body until the bit

just touches the ﬂ at surface. Tighten the lock lever at this

point. (Fig. 5)

(5) Tighten pole lock knob. Align the depth indicator with the

“0” graduation of scale.

(6) Loosen pole lock knob, and raise until indicator aligns

with the graduation representing the desired cutting

depth. Tighten pole lock knob.

(7) Loosen the lock lever and press the tool body down until

the stopper block to obtain the desired cutting depth.

Your router allows you to ﬁ nely adjust depth of cut.

(1) Attach knob to ﬁ ne adjustment knob. (Fig. 6)

(2) Turn the quick adjustment lever in a clockwise direction

until the quick adjustment lever stops with the stopper

screw. (Fig. 7)

If the quick adjustment lever does not stop with the

stopper screw, the bolt screw is not properly ﬁ tted.

If this occurs, slightly loosen the lock lever and press

down on the unit (router) hard from the top and turn the

quick adjustment lever again after properly ﬁ tting the bolt

screw.

(3) The depth of cut can be adjusted when the lock lever is

loosened, by turning the ﬁ ne adjustment knob. Turning

the ﬁ ne adjustment knob counterclockwise results in

shallower cut, whereas turning it clockwise results in a

deeper cut.

CAUTION

Ensure that the lock lever is tightened after ﬁ nely

adjusting depth of cut. Failure to do so will result in

damage to the quick adjustment lever.

2. Stopper block (Fig. 8)

The 2 cut-depth setting screws attached to the stopper

block can be adjusted to simultaneously set 3 diﬀ erent

cutting depth. Use a wrench to tighten the nuts so that

the cut-depth setting screws do not come loose at this

time.

3. Guiding the router

WARNING

Be sure to switch power OFF and disconnect the plug

from the receptacle to avoid serious trouble.

(1) Template guide adapter

Loosen the 2 template guide adapter screws, so that the

template guide adapter can be moved. (Fig. 9)

Insert the centering gauge through the hole in the

template guide adapter and into the collet chuck.

(Fig. 10)

Tighten the collet chuck by hand.

Tighten the template guide adapter screws, and pull out

the centering gauge.

(2) Template guide

Use the template guide when employing a template

for producing a large quantity of identically shaped

products. (Fig. 11)

00BookM12V2.indb700BookM12V2.indb7 2022/12/2211:02:372022/12/2211:02:37

Hikoki M12V2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info