Bedienungsanleitung Hikoki M12V2 (Seite 8 von 128) (Alle Sprachen)

816316

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

English

As shown in Fig. 12, to install insert template guide in

center hole in template guide adapter with 2 accessory

screws.

A template is a proﬁ ling mold made of plywood or

thin lumber. When making a template, pay particular

attention to the matters described below and illustrated

in Fig. 13.

When using the router along the interior plane of the

template, the dimensions of the ﬁ nished product will be

less than the dimensions of the template by an amount

equal to dimension “A”, the diﬀ erence between the

radius of the template guide and the radius of the bit. The

reverse is true when using the router along the exterior of

the template.

(3) Straight guide (Fig. 14)

Use straight guide for chamfering and groove cutting

along the materials side.

Insert the guide bar into the hole in the bar holder, then

lightly tighten the 2 wing bolts (A) on top of the bar

holder.

Insert the guide bar into the hole in the base, then ﬁ rmly

tighten the wing bolt (A).

Make minute adjustments of the dimensions between

the bit and the guide surface with the feed screw, then

ﬁ rmly tighten the 2 wing bolts (A) on top of the bar holder

and the wing bolt (B) that secures the straight guide.

As shown in Fig. 15, securely attach the bottom of the

base to processed surface of the materials. Feed the

router while keeping the guide plane on the surface of

the materials.

(4) Dust guide and Dust guide adapter (Fig. 16)

Your router is equipped with dust guide and a dust guide

adapter.

Match the 2 grooves on the base and insert the 2 dust

guide tabs in holes located in the base side from the top.

Tighten the dust guide with a screw.

The dust guide diverts cutting debris away from the

operator and directs the discharge in a consistent

direction.

By ﬁ tting the dust guide adapter into the dust guide

cutting debris discharge vent, the dust extractor can be

attached.

4. Adjusting the rotation speed

The M12V2 has an electronic control system that allows

stepless rpm changes.

As shown in Fig. 17, dial position “1” is for minimum

speed, and position “6” for maximum speed.

5. Removing the spring

The springs within the column of the router can be

removed. Doing so will eliminate spring resistance and

allows easy adjustment of cutting depth when attaching

the router stand.

(1) Loosen the 4 sub base screws, and remove the sub

base.

(2) Loosen the stopper bolt and remove it, so the spring can

be removed. (Fig. 18)

CAUTION

Remove the stopper bolt with the main unit (router) ﬁ xed

at its maximum height.

Removing the stopper bolt with the unit in a shortened

condition may cause the stopper bolt and spring to be

discharged and cause injury.

6. Cutting

CAUTION

○ Wear eye protection when operating this tool.

○ Keep your hands, face and other body parts away from

the bits and any other rotating parts, while operating the

tool.

(1) As shown in Fig. 19, remove the bit from the work pieces

and press the switch lever up to the ON position. Do

not start cutting operation until the bit has reached full

rotating speed.

(2) The bit rotates clockwise (arrow direction indicated on

the base). To obtain maximum cutting eﬀ ectiveness,

feed the router in conformance with the feed directions

shown in Fig. 20.

NOTE

If a worn bit is used to make deep grooves, a high

pitched cutting noise may be produced.

Replacing the worn bit with a new one will eliminate the

high pitched noise.

7 Trimmer Guide (Optional accessory) (Fig. 21)

Use the trimmer guide for trimming or chamfering. Attach

the trimmer guide to the bar holder as shown in Fig. 22.

After aligning the roller to the appropriate position,

tighten the two wing bolts (A) and the other two wing

bolts (B). Use as shown in Fig. 23.

MAINTENANCE AND INSPECTION

1. Oiling

To ensure smooth vertical movement of the router,

occasionally apply a few drops of machine oil to the

sliding portions of the columns and end bracket.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI AUTHORIZED

SERVICE CENTER.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must be

returned to HiKOKI Authorized Service Center for the

cord to be replaced.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 121.

For details regarding each bit type, please contact the

HiKOKI Authorized Service Center.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

00BookM12V2.indb800BookM12V2.indb8 2022/12/2211:02:372022/12/2211:02:37

Hikoki M12V2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info