Bedienungsanleitung Hikoki NT1850DBSL (Seite 20 von 420) (Alle Sprachen)

816359

Zoom out

Zoom in

Vorherige Seite

1/420

Nächste Seite

English

○ Use nail strip of more than 10 nails.

○ Use an unbroken nail strip with nails of all the same

length.

The Nailer is now ready to operate.

Removing the nails:

Pull the nail feeder (B) backward. (See Fig. 12)

Return the nail feeder (B) forward quietly while pushing

the nail feeder (A).

Pull out nails from the back of the magazine. (See

Fig. 13)

(1) Lightly press the stop lever and gently pull out the

magazine cover. (See Fig. 14)

(2) Set nail strip into the magazine and keep the points of

nails in contact with Groove. (See Fig. 15)

NOTE

The nails shown in page 16 can be loaded onto the side

guide groove of the magazine without any adjustment.

Always keep the points of nails in contact with Groove.

Magazine

Gap

Side guide

groove

Nail

Groove

(3) Slide the nail strip into the blade guide. (See Fig. 16)

(4) Conﬁ rm that nail strip is placed with side guide grooves

and Groove properly, then push the magazine cover

forward to be latched.

HOW TO USE THE NAILER

WARNING

○ NEVER point tool at yourself or others in work area.

○ Keep ﬁ ngers AWAY from trigger when not driving nails to

avoid accidental ﬁ ring.

○ Do not use the electrical cord if damaged. Have it

repaired immediately.

○ Choice of triggering method is important.

Please read and understand “1. Nailing procedures”

found below.

○ Before starting work, check the nailing operation

switching device.

This HiKOKI nailer includes a nailing operation switching

device.

Before starting work, make sure that the switching

device is properly set.

If the switching device is not set properly, the nailer will

not operate correctly.

○ Never place your face, hands or feet near ﬁ ring head

when using.

○ Do not drive nails on top of other nails or with Nailer at too

steep of an angle; nails can ricochet and hurt someone.

○ Do not drive nails into thin boards or near corners and

edges of workpiece. Nails can be driven through or away

from workpiece and hit someone.

○ Never drive nails from both sides of a wall at the same

time. Nails can be driven into and through the wall and

hit a person on the opposite side.

○ Never use Nailer which is defective or operating

abnormally.

○ Do not use Nailer as hammer.

○ Remove all remaining fasteners and battery from nailer

when:

1) doing maintenance and inspection;

2) checking proper operation of push lever and trigger;

3) attaching or removing the nose cap;

4) cleaning a jam;

5) it is not in use;

6) leaving work area;

7) moving it to another location; and

8) handing it to another person.

○ Remove battery from Nailer when:

1) loading nails;

2) turning the adjuster.

This HiKOKI nailer is equipped with a nailer operation

switching device.

Use FULL SEQUENTIAL ACTUATION MECHANISM or

CONTACT ACTUATION MECHANISM in accordance with

the work to be performed.

Explanation of the various nailing operations

○ FULL SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull

the trigger to drive the nail.

Follow the same sequence to continue driving nails.

After nailing once, nailing will not be possible again until

remove ﬁ nger from the trigger and lift the tool oﬀ the

wood surface completely.

○ CONTACT ACTUATION MECHANISM:

CONTACT ACTUATION can follow two diﬀ erent

sequences, depending on your use.

To drive several nails:

1. Pull the trigger.

2. Press the push lever against the wood to drive the

nail.

3. If the trigger is held back, a nail will be driven each

time the push lever is pressed against the wood.

To drive a single nail:

1. Press the push lever against the wood.

2. Pull the trigger to drive the nail.

3. Remove your ﬁ nger from the trigger and remove the

nailer from the wood.

[Dry-ﬁ re lockout mechanism]

The NT1865DBAL, NT1865DBSL and NT1865DA

employ a preventive mechanism for unloaded operation.

The NT1865DBAL, NT1865DBSL and NT1865DA enter

a state where the push lever cannot be pushed up. This

takes place when the magazine is not loaded with nails

or when the remaining number of nails becomes less

than 6 or 9.

CAUTION

Use caution not to throw the push lever tip onto wood

when the push lever cannot be pushed up.

1. Nailing procedures

This Nailer is equipped with the push lever and does not

operate unless the push lever is depressed.

There are two methods of operation to drive nails with

this Nailer.

They are:

1. Intermittent operation (Trigger ﬁ re):

2. Continuous operation (Push lever ﬁ re):

(1) Intermittent operation (Trigger ﬁ re)

Use the FULL SEQUENTIAL ACTUATION MECHANISM

setting. (See Fig. 17)

WARNING

○ For intermittent operation, Set the nailing operation switch

to FULL SEQUENTIAL ACTUATION MECHANISM

(Nailing operation indicator is light in blue.) (i.e. Set to

SINGLE ACTUATION MECHANISM.)

000BookNT1865DBAL.indb20000BookNT1865DBAL.indb20 2022/06/2911:54:382022/06/2911:54:38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki NT1850DBSL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info