Bedienungsanleitung Hikoki NT1850DBSL (Seite 22 von 420) (Alle Sprachen)

816359

Zoom out

Zoom in

Vorherige Seite

1/420

Nächste Seite

English

CAUTION

○ NEVER hit the driver blade.

○ NEVER point the tool at yourself or another person, to

avoid risk of injury by mis-ﬁ ring.

Even if the battery is removed from the nailer, there is still

energy of compressed air remaining inside.

Close guide plate and latch.

NOTE

In case of frequent jam, contact a HiKOKI authorized

service center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to remove all remaining fasteners and battery

from the nailer before maintenance and inspection.

1. Inspecting the magazine

Remove battery from the Nailer.

Clean the magazine. Remove dust and wooden

chips which may have accumulated in the magazine.

CAUTION

Check that the nail feeder slides smoothly by pulling it

with ﬁ nger.

If not smooth, nails can be driven at an irregular angle

and hurt someone.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

5. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

6. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Noise Information

Noise characteristic values in accordance with EN 60745:

The typical A-weighted single-event sound power level

LWA,1s,d = 92 dB

The typical A-weighted single-event emission sound

pressure level at work station LpA,1s,d = 81 dB

Uncertainty KpA: 3 dB

These values are tool-related characteristic values and

do not represent the noise development at the point of

use. Noise development at the point of use will for example

depend on the working environment, the workpiece, the

workpiece support and the number of driving operations,

etc.

Depending on the conditions at the workplace and the form

of the workpiece, individual noise attenuation measures

may need to be carried out, such as placing workpieces on

sound-damping supports, preventing workpiece vibration by

means of clamping or covering, etc.

In special cases it is necessary to wear hearing protection

equipment.

Vibration Information

The typical vibration characteristic value in accordance with

EN 60745: 2.6 m/s2

Uncertainty K: 1.5 m/s2

This values is a tool-related characteristic value and

does not represent the inﬂ uence to the hand-arm-system

when using the tool. An inﬂ uence to the hand-arm-system

when using the tool will for example depend on the gripping

force, the contact pressure force, the working direction, the

adjustment of energy supply, the workpiece, the wrokpiece

support.

000BookNT1865DBAL.indb22000BookNT1865DBAL.indb22 2022/06/2911:54:392022/06/2911:54:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki NT1850DBSL Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info