Bedienungsanleitung Hikoki W18DB (Seite 10 von 204) (Alle Sprachen)

816375

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

English

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 3 2

Charging 4 2

Changing bit*152

Selection operating mode / Switch

operation*263

Mounting and removing the hook 7 3

How to use the LED light*383

Setting the direction of rotation,

engaging the transporting safety

device (switch-on lock) *493

Working with stopper*510 4

Remaining battery indicator*6

(on tool body) 11 4

Remaining battery indicator

(on battery) 12 4

Selecting accessories ―193

*1 Changing bit

WARNING

Prevent inadvertent starting: Set manual mode and

remove battery pack from the tool before performing any

retooling.

Inserting and removing the bit:

Remove the stopper.

Insert: Insert the bit in the magnetic bit holder.

Remove: Pull the bit from the magnetic bit holder using

pliers.

Attach the stopper again:

turn and engage in position when mounted.

NOTE

The magnetic bit holder may be removed from the

spindle if the sleeve is pulled back.

*2 Selection operating mode, switch on / oﬀ

Set the required operating mode on the dial.

NOTE

When the motor is running, the spindle does not start

until the spindle is pushed in.

Manual mode

Switch on: press the trigger switch. Press in the trigger to

increase the rotational speed.

To switch oﬀ release the trigger switch.

Automatic mode

The tool starts automatically when the spindle is pushed

in. This facilitates convenient work. In order to enable

automatic mode, brieﬂ y press the trigger switch.

NOTE

The tool switches to sleep mode after 15 minutes without

use. To activate again: press the trigger switch brieﬂ y.

WARNING

Risk of injury from inadvertent automatic machine start-

up. In automatic mode, do not touch any rotating parts

such as spindle, bit or magnetic bit holder.

Impulse mode

Protruding screws can be precisely countersunk using

this function. Press trigger switch and countersink the

screw with the attached stopper. To switch oﬀ release

the trigger switch.

NOTE

○ If the amount of protrusion of the screw is small, the

screw may not tighten.

○ In that case, remove the stopper and make adjustments

in Manual mode.

*3 How to use the LED light

NOTE

The light goes out automatically 10 seconds after the

switch is released.

*4 Setting the direction of rotation, engaging the

transporting safety device (switch-on lock)

CAUTION

Only activate the rotation selector switch when the motor

has completely stopped.

00BookW18DA.indb1000BookW18DA.indb10 2022/05/2318:06:012022/05/2318:06:01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki W18DB Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info