Bedienungsanleitung Hikoki W18DB (Seite 11 von 204) (Alle Sprachen)

816375

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

English

*5 Working with stopper

The depth of screw can be set by turning the setting

sleeve. On rotation of the knurled screw corresponds to

a drill depth of around 1.5 mm.

Adjust the setting sleeve so that the screw head is

approx. 2 mm outside the stop sleeve when applying the

screw.

Insert a screw as a test. Correct the screw depth if

necessary.

CAUTION

When screwing in crosshead screws, press the machine

with the bit ﬁ rmly against the screw until the screw is

fully inserted; otherwise the bit could slip out of the cross

recess and damage the material.

*6 Remaining battery indicator (on tool body)

When using a battery with a remaining battery indicator,

please refer to the indicator lamp on the battery for the

battery remaining power.

LED LIGHT WARNING SIGNALS

This product features functions that are designed to protect

the tool itself as well as the battery. If any of the safeguard

functions are activated during operation, the LED light will

blink three times. (See Table 3) When any of the safeguard

functions are triggered, immediately remove your ﬁ nger

from the switch and follow the instructions described under

corrective action. After performing the corrective action,

if the product does not operate when the trigger switch is

pulled (or if the LED light blinks), remove the battery, wait for

about 10 seconds, then insert the battery again.

Table 3

Safeguard

Function LED Light Display Corrective Action

Overload

Protection Blinks three times. Remove the cause of

the overload.

Low Voltage

Protection Recharge the

battery.

MAINTENANCE AND INSPECTION

WARNING

Be sure to turned oﬀ the switch and remove the battery

before maintenance and inspection.

1. Inspecting the bit

Since continued use of a worn bit may cause overloading

of the motor. Replace the bit with a new one as soon as

excessive wear is noticed.

2. Clean stiﬀ stopper

If the depth setting is stiﬀ , the stopper can be dismantled

without using tools. To do this, turn the setting sleeve

clockwise until it becomes loose from the union sleeve.

Twist out the stop sleeve and clean thread.

NOTE

○ Only clean or vacuum mechanically. Do not use oils or

greases.

○ Regularly remove and clean the stopper.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

4. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

5. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

6. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

Particles may become deposited inside the power tool

during operation. This impairs the cooling of the power

tool.

The power tool should be cleaned regularly, often and

thoroughly through all front and rear air vents using a

vacuum cleaner. Prior to this operation, separate the

power tool from the power source and wear protective

goggles and a dust mask.

7. Environmental protection

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

8. Storage

Store the impact driver and the battery in a place in

which the temperature is less than 40°C and out of reach

of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

00BookW18DA.indb1100BookW18DA.indb11 2022/05/2318:06:012022/05/2318:06:01

Hikoki W18DB Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info