Bedienungsanleitung Hitachi C 10FCB (Seite 8 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

505935

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

Bolt length should be at least 25 mm plus the thickness

of the work bench.

For example, use 8mm × 50 mm bolts for a 25 mm

thick work bench.

ADJUSTING THE POWER TOOL PRIOR TO USE

CAUTION

Make all necessary adjustments before inserting the

plug in the power source.

1. Check to see that the safety cover operates smoothly.

CAUTION

⅜ This compound saw is equipped with a saw head lock

as safety device.

⅜ To lower the saw head to cut, the lock must be released

by pressing the lever with your thumb.

(1) When you push down the handle while pushing the

lever, check that the safety cover revolves smoothly

(Fig. 6).

(2) Next, check that the safety cover returns to the original

position when the handle is raised.

2. Checking the saw blade lower limit position (Fig. 7)

Check that the saw blade can be lowered 41 mm to 42

mm below the table insert.

If necessary, adjust as follows:

(1) Loosen the 8 mm lock nut on the 8 mm depth

adjustment bolt.

(2) Turn the 8 mm depth adjustment bolt as necessary to

set the lower limit position. The saw blade goes up

when the 8 mm depth adjustment bolt is turned

counterclockwise and down when it is turned

clockwise.

(3) Once the adjustment is complete, fully tighten the 8

mm lock nut.

CAUTION

Before tightening the 8 mm lock nut, confirm that the

saw blade is adjusted so that it will not contact into

the table.

PRACTICAL APPLICATIONS

CAUTION

⅜ It is dangerous to remove or install the wrokpiece

while the saw blade is turning.

⅜ When sawing, clean off the shavings from the

turntable.

⅜ If the shavings accumulate too much, the saw blad

from the cutting material will be exposed. Never

subject your hand or anything else to go near the

exposed blade.

1. Tightly secure the material by vise assembly to be

cut so that it does not move during cutting.

2. Switch operation.

Pulling the trigger turns the switch on. Releasing the

trigger turns the switch off.

3. Cutting a groove on the table insert.

A groove has to be cut in the table insert, before

starting operation. Secure a place of wood about 40

mm wide to the turntable with the vise assembly, to

prevent the breakage of the table insert. After the

switch has been turned on and the saw blade has

reached maximum speed, slowly lower the handle to

cut a groove on the table insert.

CAUTION

⅜ Do not cut the groove too quickly; otherwise the table

insert might become damaged.

4. Using the vise assembly (Standard accessory) (Fig.

(1) The vise assembly can be mounted on either the left

fence {Fence (B)} or the right fence {Fence (A)} by

loosening the 6 mm wing bolt (A).

(2) The screw holder can be raised or lowered according

to the height of the workpiece by loosening the 6 mm

wing bolt (B). After the adjustment, firmly tighten the

6 mm wing bolt (B) and fix the screw holder.

(3) Turn the upper knob and securely fix the workpiece

in position.

WARNING

⅜ Always firmly clamp or vise to secure the workpiece

to the fence; otherwise the workpiece might be thrust

from the table and cause bodily harm.

CAUTION

⅜ Always confirm that the motor head does not contact

the vise assembly when it is lowered for cutting. If

there is any danger that it may do so, loosen the 6

mm wing bolt (B) and move the vise assemlby to a

position where it will not contact the saw blade.

5. Cutting operation

(1) After turning on the switch and checking that the saw

blade is rotating at maximum speed, slowly push

down the handle while holding down the lever and

bring the saw blade in the vicinity of the material to

be cut.

(2) When the saw blade contacts the workpiece, push the

handle down gradually to produce cutting.

(3) When the cutting (or desired cutting-in) has been

completed, raise the handle up to the retract position.

(4) Turn the tool OFF after each cutting operation is

completed, and allow the saw blade to come to a

complete stop before preparing for the next operation.

CAUTION

⅜ Increased pressure on the handle does not necessarily

mean faster cutting of the workpiece. On the contrary,

too much force may result in overload of the motor

and/or decreased cutting efficiency.

⅜ Ensure the switch is turned OFF and the plug is

removed from the power outlet when work has been

completed.

6. Miter cutting procedure side handle (Fig. 8)

(1) Loosen the side handle.

(2) Adjust the turntable until the indicator aligns with the

desired setting on the miter angle.

(3) Re-tighten the side handle to secure the turntable in

the desired position.

CAUTION

Never remove the side handle; use of the tool without

it would be hazardous.

To prevent an accident or personal injury always firmly

tighten the miter handle.

NOTE

⅜ Positive stops are provided at the right and left of the

0° center setting, at 15°, 22.5°, 30°, 45° and 60° right

and 15°, 22.5°, 30° and 45° left settings.

Check that the miter angle scale and the tip of the

indicator are properly aligned.

⅜ Operation of the power tool with the miter angle scale

and indicator out of alignment, or with the miter

handle not properly tightened, will result in poor

cutting precision.

C10FCB/1-E,65E 6/21/02, 5:35 PM7

Hitachi C 10FCB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info