Bedienungsanleitung Hitachi C 10FCB (Seite 9 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

505935

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

7. Bevel cutting procedure (Fig. 9)

(1) Loosen the clamp handle and bevel the saw blade to

the left.

(2) Adjust the bevel angle to the desired setting while

watching the bevel angle scale and indicator, then

secure the clamp lever.

WARNING

⅜ In the case of left bevel cutting, turn the sub fence

(Fig.1) counterclockwise. Unless it is turned

counterclockwise, the main body or saw blade may

contact the sab fence, resulting in an injury.

⅜ When the workpiece is secured on the left side of the

blade, the short cut-off portion will come to rest on

the right side of the saw blade. Always turn the power

off and let the saw blade stop completely before

raising the handle from the workpiece.

⅜ If the handle is raised while the saw blade is still

rotating, the cut-off piece may become jammed

against the saw blade causing fragments to scatter

about dangerously.

8. Compound cutting procedure

Compound cutting can be performed by following the

instructions in 6 and 7 above. At a bevel of 45° and a

miter angle of 45°.

WARNING

⅜ Always secure the workpiece with the right hand side

for compound cutting.

⅜ Never rotate the turntable to the right for compound

cutting, because the saw blade might then contact the

clamp or vise that secures the workpiece, and cause

personal injury or damage.

9. Installing the holders (Optional accessory)(Fig. 4)

The holders help keep longer workpieces stable and

in place during the cutting operation.

(1) Use a steel square for aligning the upper edge of the

holders with the base surface.

(2) After aligning, secure the holders with the 6 mm wing

bolts.

CAUTION

⅜ When transporting or carrying the tool, do not grasp

the holder.

⅜ There is the danger of the holder slipping out of the

base. Grasp the handle instead of the holder.

10. Stopper (Optional accessory) for precision cutting

(Fig. 5.)

The stopper facilitates continuous precision cutting

in lengths of 255 mm to 420 mm. To install the stopper,

attach it to the holder with the 6 mm wing bolt.

MOUNTING AND DISMOUNTING SAW BLADE

WARNING

To prevent an accident or personal injury, always turn

off the trigger switch and disconnect the power plug

from the receptacle before removing or installing a

blade.

1. Mounting the saw blade (Fig. 10, Fig. 11 and Fig. 12)

(1) Loosen the 6 mm wing bolt holding the spindle cover

by turning it left more than two turns.

(2) Rotate the spindle cover.

(3) Press in lock lever and loosen bolt with 10mm box

wrench.

Since the bolt is left-hand threaded, loosen by turning

it to the right.

NOTE

⅜ If the lock lever cannot be easily pressed in to lock the

spindle, turn the bolt with 10 mm box wrench while

applying pressure on the lock lever.

⅜ The saw blade spindle is locked when the lock lever

is pressed inward.

(4) Remove the bolt and washer (B)

(5) Lift the safety cover and mount the saw blade.

WARNING

When mounting the saw blade, confirm that the

rotation indicator mark on the saw blade and the

rotation direction of the gear case are properly

matched.

(6) Thoroughly clean washer (B), collar (A) and the bolt,

and install them onto the saw blade spindle.

(7) Press in the lock lever and tighten the bolt by turning

it to the left by 10mm box wrench.

(8) Rotate the spindle cover unitl hook in spindle cover

is in the original position. Then, tighten the 6 mm wing

bolt.

CAUTION

⅜ Confirm that the lock lever has returned to the retract

position after installing or removing the saw blade.

⅜ Tighten the bolt so it does not come loose during

operation.

⅜ Confirm that the bolt has been properly tightened

before the power tool is started.

⅜ Confirm that the safety cover has closed position.

2. Dismounting the saw blade

Dismount the saw blade by reversing the mounting

procedures described in paragraph 1 above.

The saw blade can easily be removed after lifting the

safety cover.

CAUTION

⅜ Never attempt to install saw blades except

235 mm – 255 mm in diameter and 2.1 mm - 2.7 mm

thickness.

MAINTENANCE AND INSPECTION

WARNING

To avoid an accident or personal injury, always

confirm the trigger switch is turned OFF and that the

power plug has been disconnected from the

receptacle before performing any maintenance or

inspection of this tool.

1. Inspecting the saw blade

Since use of a dull saw blade will degrade efficiency

and cause possible motor malfunction, sharpen or

replace the saw blade as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, re-tighten them immediately. Failure to do

so could result in serious hazard.

3. Inspecting the carbon brushes (Fig. 13)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush could result in motor trouble, replace a carbon

brush with a new one when it becomes worn to or

near the “wear limit”. In addition, always keep carbon

brushes clean and ensure that they slide freely within

the brush holders.

4. Replacing a carbon brushes

Disassemble the brush cap with a minus-head

screwdriver. The carbon brushes can then be easily

removed.

C10FCB/1-E,65E 6/21/02, 5:35 PM8

Hitachi C 10FCB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info