Bedienungsanleitung Hitachi C6MEY (Seite 4 von 164) (Alle Sprachen)

616691

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

English

14. The saw blades range should be from 165 mm to

162 mm.

15. Disconnect the plug from the receptacle before carrying

out any adjustment, servicing or maintenance.

16. Be careful of brake kickback.

This circular saw features an electric brake that functions

when the switch is released. As there is some kickback

when the brake functions, be sure to hold the main body

securely.

17. Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

18. Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

19. When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

20. Avoid cutting in the state where the base has ﬂ oated up

from the material.

When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless

in the material until the blade comes to a complete

stop. Never attempt to remove the saw from the work

or pull the saw backward while the blade is in motion or

KICKBACK may occur. Investigate and take corrective

actions to eliminate the cause of blade binding.

21. Support large panels to minimize the risk of blade

pinching and KICKBACK. Large panels tend to sag

under their own weight (Fig. 3). Supports must be

placed under the panel on both sides, near the line of cut

and near the edge of the panel as shown in Fig. 2.

To minimize the risk of blade pinching and kickback.

When cutting operation requires the resting of the saw

on the work piece, the saw shall be rested on the larger

portion and the smaller piece cut oﬀ .

22. Use extra caution when making a “Pocket Cut” into

existing walls or other blind areas. The protruding blade

may cut objects that can cause KICKBACK.

NEVER place your hand or ﬁ ngers behind the saw

(Fig. 4). If kickback occurs, the saw could easily jump

backwards over your hand, possibly causing severe

injury.

23. WARNING: It is important to support the work piece

properly and to hold the saw ﬁ rmly to prevent loss

of control which could cause personal injury. Fig. 5

illustrates typical hand support of the saw.

24. Place the wider portion of the saw base on that part

of the work piece which is solidly supported, not on

the section that will fall oﬀ when the cut is made. As

examples, Fig. 6 illustrates the RIGHT way to cut oﬀ the

end of board, and Fig. 7 the WRONG way. If the work

piece is short or small, clamp is down.

DON’T TRY TO HOLD SHORT PLACES BY HAND!

25. Never attempt to saw with the circular saw held upside

down in a vise. This is extremely dangerous and can

lead to serious accidents (Fig. 8).

26. Should lever remain loosened, it will create a very

hazardous situation. Always thoroughly clamp it.

(Fig. 12)

27. It is very hazardous to allow wing bolt to remain loosened.

Always thoroughly clamp it. (Fig. 23)

28. Prior to cutting operation, make sure the material you

are going to cut. If the material to be cut is expected to

generate harmful / toxic dusts, make sure the dust bag

or appropriate dust extraction system is connected with

dust outlet tightly.

Wear the dust mask additionally, if available.

○ Before starting to saw, conﬁ rm that the saw blade

has attained full-speed revolution.

○ Should the saw blade stop or make an abnormal

noise while operating, promptly turn OFF the switch.

○ Always take care in preventing the power cord from

coming near to the revolving saw blade.

○ Using the circular saw with the saw blade facing

upwards or sideways is very hazardous. Such

uncommon applications should be avoided.

○ When cutting materials, always wear protective

glasses.

○ When ﬁ nished with a job, pull out the plug from the

receptacle.

29. After having attached the saw blade, reconﬁ rm that the

lock lever is ﬁ rmly secured in the prescribed position.

30. Do not expose directly your eye to the light by looking

into the light.

If your eye is continuously exposed to the light, your eye

will be hurt.

NAMES OF PARTS (Fig. 1 – Fig. 26)

Switch

Switch lock

Cutting depth lever

Incline wing nut

Guide fastener wing bolt

Lower guard

Bolt

Washer (B)

Saw blade

Guide piece

Base

Incline lever

Lock lever

Guide fastener wing bolt

Stopper lever

LED light

Cord holder

Handle

(

Mode selector switch

)

Silent mode indicator lamp

Lighting switch

Long guide

Guide

Fluorine plate

Dust collection adapter

Box wrench

Washer (A)

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi C6MEY Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info