Bedienungsanleitung Hitachi C6MEY (Seite 6 von 164) (Alle Sprachen)

616691

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

English

Inclined cutting (–5° direction) 24 154

Dismounting the saw blade 25 155

Mounting the saw blade 26 155

Selecting accessories ― 156

(*1) About the mode select function

Each time the mode selector switch is pushed, the

operation mode changes.

When Silent mode is selected, the Silent mode indicator

lamp lights up.

Silent mode reduces maximum motor RPM enabling

eﬃ cient work with less noise.

If the load increases while the motor is operating in

Silent mode, it automatically changes to Power mode.

Additionally, if the load decreases again, it automatically

returns to Silent mode.

In Power mode, no change is made to Silent mode even

when the load decreases.

Mode No-load speed

Power 4100 min

-1

Silent 2500 min

-1

NOTE

○ You cannot change the mode unless the power plug is

connected to a receptacle and the switch is pulled once.

○ Even if the switch is turned on and oﬀ or the power plug

is disconnected and connected, this unit will maintain the

mode that you set.

MAINTENANCE AND INSPECTION

1. Inspecting the saw blade

Since use of as dull saw blade will degrade eﬃ ciency

and cause possible motor malfunction, sharpen or

replace the saw blade as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Replacing supply cord

If the replacement of the supply cord is necessary, this

has to be done by the manufacturer of this agent in order

to avoid a safety hazard.

5. Maintenance of lower guard

For safe and proper working, always keep the machine

and ventilation slots clean. The lower guard must

always be able to more freely and retract automatically.

Therefore, always keep the area around the lower guard

clean. Remove dust and chips by blowing out with

compressed air or with a brush.

6. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

7. Storage

Please avoid locations such as the following for the

storage of products and accessories that are not being

used, and store them in a safe and dry place.

NOTE

○ Do not store them in locations where children can

reach them or easily get hold of them.

○ Do not store them in locations where rain can fall

such as under the eaves of a house, or where there

is humidity.

○ Do not store them in locations where there are

sudden changes in humidity or there is direct

sunlight.

○ Do not store them in locations where there are

volatile substances which have a risk of catching ﬁ re

or exploding.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 94 dB (A)

Measured A-weighted sound pressure level: 83 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Cutting chipboard:

Vibration emission value a

= 2.0 m/s

Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi C6MEY Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info