Bedienungsanleitung Hitachi CL10D2 (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

565914

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

(2) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown

in Table 2.

Table 2 Charging time (At 20°C)

NOTE:

The charging time may vary according to embient

temperature and power source voltage.

4. Disconnect the charger’s power plug from the

receptacle on completion of recharging.

5. Hold the charger firmly and pull out the battery.

NOTE:

After charging, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an

extended period is not activated, the electric

discharge might be low when using them the first

and second time. This is a temporary phenomenon,

and normal capacity will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION:

䡬 If the battery has been heated just after operation

(or due to sunlight, etc.), the charger’s pilot lamp

will not light in red. In such a case, first let the

battery cool, then start charging.

䡬 When the pilot lamp frickers in red quickly (at 0.2-

second intervals), check for and take out any foreign

objects in the charger’s battery installation hole. If

there are no foreign objects, it is probable that the

battery or charger is malfunctioning. Take it to your

authorized Service center.

䡬 Since the built-in micro computer takes about 3

seconds to confirm that the battery being charged

with UC14YFA is taken out, wait for a minimum of

3 seconds before reinserting it to continue charging.

If the battery is reinserted within 3 seconds, the

battery may not be properly charged.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by

following the precautions.

2. Confirm that the battery is mounted correctly

3. Setting the forward/reverse switching button

(1) Push the forward/reverse switching button from the

right as shown in Fig. 4-1. Cutting is possible in

the

position (Fig. 4-1).

(2) By setting the forward/reverse switching button in

the

(central) position as shown in Fig. 4-2, the

motor will not operate even if the trigger switch

is pulled. When carrying or storing the main unit

or when stopping operations, set the forward/reverse

switching button to the

position (Fig. 4-2).

Table 1

Indications of the lamps

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Malfunction in the battery or the charger

The battery temperature is high, making

recharging impossible.

Charger

UC14YFA

Battery

EB12 Approx. 30 min.

EB12B Approx. 50 min.

EB1230H Approx. 70 min.

01Eng_CL10D2_WE 1/28/08, 17:456

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CL10D2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info