Bedienungsanleitung Hitachi CL10D2 (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

565914

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

(3) Use the accessory hexagonal wrench to insure that

the hex. socket hd. bolt for attaching the cutter is

securely tightened (Fig. 5). Using the equipment

while the bolt is loose could cause damage to the

main unit and cutter.

(4) Depending on the size of the studs it may be

necessary to attach special spacers to the cutter.

1 When using the M10, M8 or M6 cutter

Check and confirm that the accessory M6, M8 or

M10 spacers are correctly inserted respectively

between bracket (A) and the cutter and bracket (B)

and the cutter (Fig. 5).

CAUTION:

If the spacers are not attached or if spacers of the

wrong size are used, the threads of the cutter and

the studs will not properly mesh, thereby causing

damage to the studs and the cutter edge. Be sure

to attach spacers correctly.

2 When using the W3/8" cutter

No spacers are required. Check and confirm that

only the cutter is attached.

For details, refer to the section on “Cutter life and

replacement” on page 9.

5. Correctly insert the stud guide

The stud guide is used to prevent tilting during

cutting of studs. Correctly adjust the dial calibration

to the mark (



) depending on the size of the stud

to be cut (Fig. 6).

CAUTION:

If the size of the stud and the dial position to do

not agree, the cut section may be subjected to burrs

or its shape may be distorted, which may result in

damage to the main unit.

Fig. 6

HOW TO USE

CAUTION:

䡬 Never bring the cutter near your fingers when

operating the trigger switch.

䡬 When cutting short studs, take caution as to not

place your fingers in the space between the short

stud and main unit, such as the guard section (see

Fig. 7), battery, etc.

䡬 After cutting, the cut section of the stud is very

sharp and therefore dangerous. Be very careful

when handling the stud.

(3) Push the forward/reverse switching button from the

left as shown in Fig. 4-3 to set to the

position.

With the button held down, pull the trigger switch

so that the cutter can be removed from the stud.

Only set to this position if the rechargeable battery

is worn out and the unit stops operating during

cutting. Immediately turn off the switch after the

cutter has been removed from the stud.

If you remove your finger, the forward/reverse

switching button automatically returns to the

position (Fig. 4-2).

CAUTION:

Do not attempt to cut in the

position (Fig. 4-

3). If you attempt to cut in this position, there will

be an overload on the motor and cutting will not

be possible. Never apply excessive force to the

main unit as this can cause damage to the unit.

Fig. 4-1 Fig. 4-2 Fig. 4-3

4. Check the cutter size, attachment direction,

attachment bolt and spacer

(1) The cutter size differs according to the size of the

studs to be cut. Make sure that a cutter is attached

that conforms to the size of the studs to be cut.

(2) Cutter attachment includes directionality. Make sure

that the cutter has been attached so that the side

without the notch on the cutter can be seen on

bracket (A) (movable side) when the main unit is

viewed from the front or that the notch on the cutter

surface can be seen on bracket (B) (fixed side).

Fig. 5

Forward/reverse switching button

(Equipment as seen from the handle side)

Removal during

cutting operations

During cutting

operations

Does not

rotate

Bracket (A)

(movable side)

Spacer

(used only with

M6, M8 or M10)

Notch side

Bracket (B)

(fixed side)

Spacer

(used only with

M6, M8 or M10)

Hex. socket

hd. bolt

Side without

notch

Screw size

display

Dial

Mark

Stud guide

01Eng_CL10D2_WE 1/28/08, 17:457

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CL10D2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info