Bedienungsanleitung Hitachi CM-N10000 (Seite 7 von 30) (Englisch)

654256

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

-7- -8-

2. Connect the power adaptor to the main body and outlet, and press the power switch.

(Fig. 4)

3. Select the power level ("HIGH" or "LOW") with the level selector button.

●

The “LOW” level indicator lamp will light, and the “CLEANSING” mode indicator lamp

will flash. If another mode indicator lamp flashes, press the mode selector button to

select “CLEANSING.”

Every time the level selector button is pressed, the potential power level is

switched between "HIGH" and "LOW". The vibration power does not change.

Select the power level ("HIGH" or "LOW") with the level selector button

according to your skin condition.

●

The previous power level ("HIGH" or "LOW") is stored by the memory function.

Use at the "LOW" level is recommended for people who use this product for the first

time and who feel something unusual.

Make sure to hold the body with your hand touching either of the right and left side

plates.

●

5. Apply the cotton puff to your skin and move the product slowly. (Fig. 6)

●

Apply head onto skin and slowly head from center to the outside of your face.

Use this product within approximate 5 minutes.

After 5 minutes have elapsed, the product will stop automatically.

The mode indicator lamp will light, and the product will start to vibrate.

The device will not vibrate unless you apply the cotton puff to your skin while

touching the side plate. (Skin sensing function)

If the head is not vibrating, the product is not working.

Power will be automatically turned off if device is unused for 30 seconds.

(Auto-off function)

4. Hold the main body by the side plate. (Fig. 5)

●

If the moisture in the cotton puff becomes insufficient or if it is hard to slide, add more

toner.

●

Do not use this device on the same part of your skin for more than 10 seconds.

If you feel slight current stimulation (a tingling sensation) during use, press the

level selector button to set the "LOW" level.

If you still feel a "tingling sensation," add more toner.

How to use

If you sense anything wrong with your skin or body during use,

immediately stop using this product and consult a dermatologist.

(Cause of an accident or poor health condition)

Do not use this product around eyes and ears.

(Cause of an accident or poor physical condition)

CAUTION

Do not keep the cotton puff on the same part of your skin, but

move it around. (Cause of skin trouble or poor health condition)

Step 1

CLEANSING

This mode is to remove fine dirt remaining in pores which cannot be removed by simple

washing and make your skin suitable for

MICRO-PAT

1. After washing your face, saturate the cotton puff attached to the head with toner.

Use your regular toner or wiping lotion with an exfoliating effect.

(Do not use a milky lotion or gel.)

Saturate the cotton puff with the toner until it seeps through the cotton puff to the

rear side.

●

Some toners (made only of mineral spring water or water, etc.) may not show

effects sufficiently.

8. Remove the ring and the cotton puff.

6. An automatic stop is made when around 5 minutes have elapsed.

(Auto-off function)

You will know the automatic stop with the ending sound.

●

Wipe off the surface of the head with tissue, etc.

●

Do not use the cotton puff again once it is used because its reuse will cause

skin trouble.

●

1. Evenly spread your regular

toner

over your face.

Step 2 "

MICRO-PAT

This mode is to effectively stimulate and loosen up your skin to allow moisturizing

ingredients to easily permeate your skin.

Wipe the

toner

off your hands.

●

Make sure to use the attached power adaptor on an AC power supply of 100 – 240V.

(This product is not rechargeable.)

7. After use, make sure to pull out the power adaptor from the outlet. (Fig. 7)

For continued use of the next mode, keep the power adaptor connected.

Pull out holding the plug portion.

●

The “LOW” level indicator lamp will light, and the “MICRO-PAT” mode indicator lamp

will flash. If another mode indicator lamp flashes, press the mode selector button to

switch the mode.

If the power switch is pressed after the end of the "

CLEANSING

" mode, the

MICRO-PAT

" mode is set automatically.

2. Check that the power adaptor is connected to the main body, and press the power switch.

(Fig. 8)

3. Select the power level ("HIGH" or "LOW") with the level selector button.

●

Every time the level selector button is pressed, the power level is

switched between "HIGH" and "LOW"

The vibration power does not change.

Select the power level ("HIGH" or "LOW") with the level selector button

according to your skin condition.

Use at the "LOW" level is recommended for people who use this product for the first

time and who feel something unusual.

Make sure to hold the body with your hand touching either of the right and left side

plates.

●

4. Hold the main body by the side plate. (Fig. 9)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CM-N10000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info