Bedienungsanleitung Hitachi CM-N10000 (Seite 8 von 30) (Englisch)

654256

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

-9- -10-

8. Wipe the

toner

off the head and main body with tissue, etc.

●

The device will not vibrate unless you apply the head to your skin while touching

the side plate. (Skin sensing function)

If the head is not vibrating, the product is not working.

Power will be automatically turned off if device is unused for 30 seconds.

(Auto-off function)

●

Step 3 "

MOISTURIZE

3. Check that the power adaptor is connected to the main body, and press the power switch.

(Fig.10)

The “LOW” level indicator lamp will light, and the “MOISTURIZE” mode indicator

lamp will flash. If another mode indicator lamp flashes, press the mode selector

button to switch the mode.

This mode is to give moisturizing care by making the moisturizing ingredients of the

toner

permeate your skin.

1. Attach a new cotton puff to the main body, and fix it with the ring.

●

Do not use a milky lotion or gel. Saturate the cotton puff with the

toner

until it

seeps through the cotton puff to the rear side.

●

For attaching a cotton puff, see "Preparation for use."

2. Saturate the cotton puff with your regular

toner

If the power switch is pressed after the end of the "

MICRO-PAT

" mode, the

MOISTURIZE

mode is set automatically.

5. Apply the head directly to your skin and move it slowly. (Fig. 6)

●

Use this product within approximate 5 minutes.

After 5 minutes have elapsed, the product will stop automatically.

The mode indicator lamp will light, and the product will start to vibrate.

CAUTION

Apply head from center to the out side of your face.

Do not keep the head on the same part of your skin, but move it

around. (Cause of skin trouble or poor health condition)

Do not use this device on the same part of your skin for more than 10 seconds.

If you feel slight current stimulation (a tingling sensation) during use, press the

level selector button to set the "LOW" level.

6. An automatic stop is made when around 5 minutes have elapsed. (Auto-off function)

You will know the automatic stop with the ending sound.

●

Make sure to hold the body with your hand touching either of the right and left side

plates.

●

6. Apply the cotton puff to your skin and move the product slowly. (Fig. 6)

●

Apply head from center to the out side of your face.

Use this product within approximate 5 minutes.

After 5 minutes have elapsed, the product will stop automatically.

The mode indicator lamp will light, and the product will start to vibrate.

The device will not vibrate unless you apply the cotton puff to your skin while

touching the side plate. (Skin sensing function)

If the head is not vibrating, the product is not working.

Power will be automatically turned off if device is unused for 30 seconds.

(Auto-off function)

5. Hold the main body by the side plate. (Fig. 5)

●

If the moisture in the cotton puff becomes insufficient or if it is hard to slide, add more

toner.

●

Do not use this device on the same part of your skin for more than 10 seconds.

CAUTION

Do not keep the cotton puff on the same part of your skin, but

move it around. (Cause of skin trouble or poor health condition)

●

If you feel slight current stimulation (a tingling sensation) during use, press the

level selector button to set the "LOW" level.

If you still feel a "tingling sensation," add more toner.

9. Remove the ring and the cotton puff.

7. An automatic stop is made when

around

5 minutes have elapsed. (Auto-off function)

You will know the automatic stop with the ending sound.

●

Wipe off the surface of the head with tissue, etc.

●

Do not use the cotton puff again once it is used because its reuse will cause

skin trouble.

4. Select the power level ("HIGH" or "LOW") with the level selector button.

●

Every time the level selector button is pressed, the potential power level is

switched between "HIGH" and "LOW"

The vibration power does not change.

Select the power level ("HIGH" or "LOW") with the level selector button

according to your skin condition.

Use at the "LOW" level is recommended for people who use this product for the

first time and who feel something unusual.

7. After use, make sure to pull out the power adaptor from the outlet. (Fig.7)

For continued use of the next mode, keep the power adaptor connected.

8. After use, make sure to pull out the power adaptor from the outlet.

(Fig. 7)

For continued use of the next mode, keep the power adaptor connected.

Step 4 “COOL-AESTHETIC”

This mode tighten the pores of your skin by a fresh cooling effect as the head section

surface is approximately 10℃ lower than the ambient temperature.

1. Remove the cotton puff, and wipe the toner off the head section.

2. Check that the power adaptor is connected to the main body, and press the power

switch. (Fig.11)

The level indicator lamp will go out, and the “COOL-AESTHETIC” mode indicator

lamp will flash. If another mode indicator lamp flashes, press the mode selector

button to switch the mode.

●

If the power switch is pressed after the end of the “MOISTURIZE” mode, the

“COOL-AESTHETIC” mode is set automatically.

Use at an ambient temperature in the range of 10 to 40℃.

(Cause of skin damage as the head is too cold if the device is used

at a lower temperature)

Hitachi CM-N10000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info