Bedienungsanleitung Hitachi CM14E (Seite 7 von 232) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

565926

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

Read this cutter operator’s manual carefully. Be sure you understand how to

operate this cutter properly before you use it.

Establish a training program for cutter operators.

Use safety footwear, snug-ﬁ tting clothing and protective gloves.

Wear eye, hearing and head protection devices. Use ballistics chaps or

pants when necessary. Clothing of ﬁ re-resistant and unmeltable material

should be worn by emergency crews exposed to ﬂ ames or high heat

conditions.

Use caution when handling fuel. Put the fuel tank caps back tightly on both

the fuel container and the cutter tank, move at least 3 m from the fuelling

point, and be sure there is no leakage of fuel from the fuel tank cap or the

fuel system before starting the engine. Avoid ignition from sparks.

DANGER

After refuelling, tighten fuel cap ﬁ rmly and check for leakage. In

case of fuel leakage repair before starting operation since there is a

danger of ﬁ re.

WARNING

Do not run the engine indoors, or where there is poor ventilation.

Engine fumes contain deadly poisonous carbon monoxide.

IMPORTANT

z Check before every use.

z After refuelling, make sure fuel does not leak or exude from around fuel

pipe, fuel grommet or fuel tank cap.

z In case of fuel leakage or exudation there is a danger of ﬁ re. Stop using

the machine immediately and request your dealer to inspect or replace.

z It is not permitted to ﬁ ll fuel above the shoulder level of fuel tank.

Operate this petrol engine cutter only in well-ventilated areas.

Do not store the unit with fuel in its tank, because a fuel leak could start a

ﬁ re.

Do not cause sparks in any area where there are ﬂ ammable materials.

Start the cutter on the ground with the cutting wheel completely in the clear.

Do not drop-start the cutter, or start it if the wheel is obstructed by the

ground or any other object.

Do not allow other persons to be nearer than 9 m when you are starting or

cutting with the cutter. Be aware that bystanders should wear hearing and

eye protection. Do not start cutting unless you have good footing and the

work area is clear.

Do not let someone hold the work you are cutting.

Adjust the wheel shield to a position where the sparks and debris from the

wheel will be thrown away from you. The wheel shield can be adjusted by

loosening the locking knob. After the position of the wheel shield is decided,

ﬁ x the wheel shield by tightening the locking knob ﬁ rmly. Do not operate if

the wheel shield is damaged, missing from the unit, improperly positioned, or

cannot be locked in proper position.

Operator Safety Precautions

3 m

Adjust Wheel Shield

Locking knob

CM14E_WE_all.indb 7CM14E_WE_all.indb 7 2008/02/05 21:09:302008/02/05 21:09:30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CM14E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info