Bedienungsanleitung Hitachi CM14E (Seite 8 von 232) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

565926

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

Keep a ﬁ rm grip on the cutter with both hands, the right hand on the rear

handle, and the left hand on the front handle when the engine is running.

Use a ﬁ rm grip with thumbs and ﬁ ngers encircling the cutter handles. A ﬁ rm

grip will help you to keep control if the cutter kickback toward you, or the

thrust of the rotating wheel pulls it away from you. Never operate the cutter

with only one hand.

Keep to the left of the cutter so that no part of your body is in line with the

cutting wheel. Keep all parts of your body away from the cutting wheel when

the engine is running.

Do all cutting at full throttle speed. Cutting at less than full speed can

damage the clutch by allowing it to slip. Accelerating from slow to full speed

while the wheel is in cutting contact may cause a violent push or pull reaction

resulting in loss of control.

It will take time for the wheel to coast to a stop after the throttle trigger is

released. Be sure to wait for rotation to stop before releasing your grip on the

cutter handles. Always shut off the engine before setting down the cutter.

Always carry the cutter with the engine stopped and the hot mufﬂ er away

from your body. Do not touch a hot mufﬂ er or cylinder.

Remove the wheel from the cutter prior to transport or storage. Store wheels

properly to avoid damage from uneven pressure, moisture and extreme

temperatures.

Do not grind on the side of an abrasive wheel, or put any side pressure on

the wheel during cutting. Avoid letting the cutter tilt or wobble off line.

Use new, properly qualiﬁ ed wheels of correct diameter, thickness and

mounting hole size. The wheel blotters and the mounting ﬂ anges should be

in good condition, and the mounting bolt should be tightened to the proper

torque.

Inspect the wheel carefully for cracks, edge damage and warping before

use. Do not use any wheel that has been dropped.

All items of adjustment and maintenance given in this operator’s manual

should be performed as necessary, and may be done by the cutter owner.

AII required items of service or adjustment not listed in this manual should

be performed only by a qualiﬁ ed HITACHI servicing dealer.

Over speeding of the engine, or wrong size pulleys in the belt transmission

can result in dangerously high wheel speeds. Install only the proper diameter

pulleys in the belt transmission. The engine no load maximum speed is

controlled by a vibration-sensitive governor. Check speed with a tachometer,

or contact your HITACHI dealer if you suspect the governor is not working

properly.

Keep to Left of

Cutting Line

Put no Side

Pressure on

the Wheel

Check for Wheel

Damage

CM14E_WE_all.indb 8CM14E_WE_all.indb 8 2008/02/05 21:09:302008/02/05 21:09:30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CM14E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info