Bedienungsanleitung Hitachi D6SH-2 (Seite 6 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566268

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

English

drill bit or damage to the drill body itself due to

the sudden movement of the drill.

Always be alert and ready to release the pushing

force when drilling through the material.

3. Switch operation:

By pulling the trigger switch and depressing the

stopper, the switch is held in the ON position for

continuous operation. To turn the drill OFF, pull the

trigger switch again and release.

4. Precautions on Boring

The drill may become overheated during operation;

however, it is sufficiently operable. Do not cool the

drill bit in water or oil.

5. Using stopper assembly (Spec. only for keyed chuck)

(Fig.1)

NOTE: The stopper rod can be fixed on whichever

side of the housing.

Adjust the stopper rod to reach a required drilling

depth. To fix it securely, use the stopper bolt.

CAUTION

A stopper assembly is not attached to products

equipped with a keyless chuck because the stopper

rod would come into contact with the keyless chuck.

A stopper assembly should never be mounted on

any product equipped with a keyless chuck in

disregard of the above warning because such action

could result in a serious accident.

6. Caution immediately after use

Immediately after use, if the Drill is still revolving

and it is placed on a location where considerable

ground chips and dust have accumulated, dust may

occasionally be absorbed into the Drill mechanism.

Always pay attention to this possibility.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to switch power OFF and disconnect the plug

from the receptacle during maintenance and inspection.

1. Inspecting the drill bit

Since use of an abraded drill bit will cause motor

malfunctioning and degraded efficiency, replace the

drill bit with a new one or resharpening without

delay when abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loosened, retighten them immediately,

Failure to do so could result in serious hazard.

3. Servicing

Consult an authorized Service Center in the event

of power tool failure.

4. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Authorized Service

Center.

This Parts List will be helpful if presented with the

power tool to the Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE:

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject of

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this

tool may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the

terminal marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the each terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound pressure level: 76 dB (A)

Uncertainty KpA: 3 dB (A).

Wear ear protection.

The typical weighted root mean square acceleration value

does not exceed 2.5 m/s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi D6SH-2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info