Bedienungsanleitung Hitachi DB 3 DL (Seite 26 von 34) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

78868

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

SPECIFICATIONS

POWER TOOL

STANDARD ACCESSORIES

1 Plus driver bit (No. 2 × 50L)............................... 1

2 Battery (EBM315)...................................................... 1

3 Charger

(UC3SFL) ............................................................

4 Plastic case ................................................................ 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

1. Battery (EBM315)

Optional accessories are subject to change without notice.

No-load speed (Low/High) 200 / 600 min

–1

Drilling

Metal Steel: 2 mm,

(Thickness 1.0 mm) Aluminum: 2 mm

Capacity Machine screw 5 mm

Driving

Wood screw

3.5 mm (diameter) × 20 mm (length)

(Requires a pilot hole)

Rechargeable battery EBM315: Li-ion 3.6 V (1.5 Ah 1 cell)

Weight 0.4 kg

APPLICATIONS

⅜ Driving and removing of machine screws, wood

screws, tapping screws, etc.

⅜ Drilling of various metals

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery release

buttons (2 pcs.) to remove the battery (see Figs. 1 and

2).

CAUTION:

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the driver drill, charge the battery as follows.

1. Connect the charger’s power cord to a receptacle.

2. Insert the battery into the charger.

Firmly insert the battery into the charger till it contacts

the bottom of the charger and checking the polarities

as shown in Fig. 3.

CHARGER

Model UC3SFL

Charging voltage 3.6 V

Weight 0.3 kg

PRECAUTIONS FOR CORDLESS DRIVER

DRILL

1. Always charge the battery at a temperature of 10 –

40°C. A temperature of less than 10°C will result in

over charging which is dangerous. The battery

cannot be charged at a temperature higher than

40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

2. When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

Do not charge more than two batteries

consecutively.

3. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

4. Never disassemble the rechargeable battery and

charger.

5. Never short-circuit the rechargeable battery. Short-

circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

6. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

7. When drilling in wall, floor or ceiling, check for

buried electric power cord, etc.

8. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use. Do not dispose

of the exhausted battery.

9. Using an exhausted battery will damage the charger.

10. Do not insert object into the air ventilation slots of

the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DB 3 DL Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DB 3 DL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info