Bedienungsanleitung Hitachi DB 3 DL (Seite 27 von 34) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

78868

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

Inserting the battery will turn on the charger (the

pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

The pilot lamp goes off to indicate that the battery is

fully charged.

CAUTION

If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may

not light. At that time cool the battery first, then

start charging.

⅜ Regarding recharging time

Table 1 shows the recharging time required according

to the type of battery.

NOTE: The recharging time may vary according to the

ambient temperature.

3. Disconnect the charger’s power cord from the

receptacle.

4. Hold the charger firmly and pull out the battery.

NOTE:

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION:

⅜ When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next

charging.

⅜ If the battery charger does not work while the battery

is mounted correctly, it is probable that the battery or

Table 1 Recharging time (approx. min.) at 20°C

Battery

voltage

(V)

Battery capacity (Ah)

1.5 Ah

3.6 V EBM315 30 min.

charger is malfunctioning. Take it to your authorized

Service Center.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by following

the precautions.

HOW TO USE

How to make the batteries perform longer

⅜ Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

1. Installing the bit

Always follow the following procedure to install driver

bit. (Fig. 4)

(1) Pull the guide sleeve forward.

(2) Insert the bit into the hexagonal hole in the socket.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION:

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

2. Removing the bit

Please do the opposite point on the method of

installing bit.

3. Automatic spindle-lock mechanism

When the main switch is off, the bit is locked in place,

and the tool can be used as a manual screwdriver.

4. Confirm that the battery is mounted correctly

5. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (see

Figs. 5 and 6).

When the shift knob is set to “LOW”, the drill rotates

at a low speed. When set to “HIGH”, the drill rotates

at a high speed.

CAUTION:

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When a large force is required for operation, set the

shift knob to “LOW”. If “HIGH” is set and the unit is

used, it may cause the motor to burn out or

malfunction prematurely.

6. Confirm the clutch dial position (See Fig. 7)

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the

clutch dial is set.

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 5, 9 ... 21” on the clutch dial, or the

black dots, with the triangle mark on the outer body.

(2) When using this unit as a drill, align the clutch dial

drill mark “

” with the triangle mark on the outer

body.

CAUTION

⅜ The clutch dial cannot be set between the numerals

“1, 5, 9 ... 21” or the black dots.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DB 3 DL Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DB 3 DL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info