Bedienungsanleitung Hitachi DS 14 DVB (Seite 35 von 42) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

78865

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

(2) Regarding the temperatures of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the table below, and batteries that have

become hot should be cooled for a while before

being recharged.

Table 2 Recharging ranges of batteries

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown

in Table 3.

Table 3 Charging time (At 20°C)

NOTE

The charging time may vary according to

temperature and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an

extended period is not activated, the electric

discharge might be low when using them the first

and second time. This is a temporary phenomenon,

and normal time required for recharging will be

restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a

while.

CAUTION

⅜ If the battery is charged while it is heated because

it has been left for a long time in a location subject

to direct sunlight or because the batetery has just

been used, the pilot lamp of the charger lights up

green. In such a case, first let the battery cool, then

start charging.

⅜ When the pilot lamp flickers in red (at 0.2-second

intervals), check for and take out any foreign objects

in the charger’s battery installation hole. If there are

no foreign objects, it is probable that the battery

or charger is malfunctioning. Take it to your

authorized Service Center.

⅜ Since the built-in micro computer takes about 3

seconds to confirm that the battery being charged

with UC14YF2/UC24YFA is taken out, wait for a

minimum of 3 seconds before reinserting it to

continue charging. If the battery is reinserted within

3 seconds, the battery may not be properly charged.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by

following the precautions.

HOW TO USE

1. Confirm the cap position (see Fig. 5)

The tightening torque of this unit can be adjusted

according to the cap position, at which the cap is

set.

(1) When using this unit as a screwdriver, line up the

one of the numbers “1, 3, 5 ... 22” on the cap, or

the white dots, with the triangle mark on the outer

body.

(2) When using this unit as a drill, align the cap drill

mark “

” with the triangle mark on the outer

body.

CAUTIONS

⅜ The cap cannot be set between the numerals “1,

3, 5 ... 22” or the white dots.

⅜ Do not use with the cap numeral between “22” and

the white line at the middle of the drill mark. Doing

so may cause damage. (See Fig. 6)

2. Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity

to the screw diameter. When too strong torque is

Temperatures at

Rechargeable batteries

which the battery

can be recharged

EB914, EB9B, EB1214L,

EB1220BL, EB1414, EB14B, –5°C – 60°C

EB18B, EB1820

EB9H, EB930H, EB1222HL,

EB1230HL, EB14H, EB1430H,

0°C – 45°C

EB18H, EB1830H

Charger

UC14YF2 UC24YFA

Battery

EB914, EB1214L,

Approx. 50 min. Approx. 40 min.

EB1414

EB9B, EB1220BL,

Approx. 60 min.

EB14B

Approx. 50 min.

EB18B, EB1820

EB9H, EB1222HL,

Approx. 70 min.

EB14H

Approx. 55 min.

EB18H

EB930H, EB1230HL,

Approx. 90 min.

EB1430H

Approx. 70 min.

EB1830H

DS9•12•14•18DVB/5-E.E65 6/21/02, 4:46 PM34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS 14 DVB Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 14 DVB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info