Bedienungsanleitung Hitachi DS 14 DVB (Seite 36 von 42) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

78865

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

Work Suggestions

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller diameter

screws.

Driving

Wood screw 1 –

For 8 mm or smaller nominal

diameter screws. (DS18DVB/

DS14DVB/DS12DVB)

For 5.5 mm or smaller nominal

diameter screws. (DS9DVB)

Wood

For 38 mm or smaller

diameters. (DS18DVB)

For 36 mm or smaller

diameters. (DS14DVB)

Drilling

For 32 mm or smaller

diameters. (DS12DVB)

For 21 mm or smaller

diameters. (DS9DVB)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 4.8 mm or smaller

nominal diameter screws.

For 24 mm or smaller

diameters. (DS18DVB)

For 18 mm or smaller

diameters. (DS14DVB/

DS12DVB/DS9DVB)

used, the screw head may be broken or be injured.

Be sure to adjust the cap position according to the

screw diameter.

(2) Tightening torque indication

The tightening torque differs depending on the type

of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 3, 5 ... 22” on the cap, and a white

dots. The tightening toque at position “1” is the

weakest and the torque is strongest at the highest

number. (See Fig. 5)

(3) Adjusting the tightening torque

Rotate the cap and line up the numbers “1, 3, 5,

... 22” on the cap, or the white dots, with the

triangle mark on the outer body. Adjust the cap in

the weak or the strong torque direction according

to the torque you need.

CAUTIONS

⅜ The motor rotation may be locked to cease while

the unit is used as drill. While operating the driver

drill, take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Change rotation speed

Operate the shift knob to change the rotational

speed. Move the shift knob in the direction of the

arrow (see Figs. 7 and 8).

When the shift knob is set to “LOW”, the drill

rotates at a low speed. When set to “HIGH”, the

drill rotates at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is “17” or “22”, it may

happen that the clutch does not engaged and that

the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt.

4. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown

in Table 4.

5. How to select tightening torque and rotational speed

Table 5

DS9•12•14•18DVB/5-E.E65 6/21/02, 4:46 PM35

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS 14 DVB Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 14 DVB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info