Bedienungsanleitung Hitachi DV10DVA (Seite 9 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

506247

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

at a low speed. When set to “H”, the drill rotates

at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “H” (high speed) and

the position of the cap is “4” or “5”, it may happen

that the clutch does not engaged and that the motor

is locked. In such a case, please set the shift knob

to “L” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt.

5. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown

Table.1.

3. Rotation to Impact changeover (See Fig. 4.).

The "Rotation (Rotation only)" and "Impact (Impact

+ Rotation)" can be switched by aligning the drill

mark "

" or the hammer mark" " to the triangle

mark of the housing.

⅜ To make holes in the metal, wood or plastic, switch

to "Rotation (Rotation only)".

⅜ To make holes in bricks or concrete blocks, switch

to "Impact (Impact + Rotation)".

CAUTION

If an operation which is normally performed at the

"Rotation" setting is performed at "Impact " setting,

the effect of making holes does not only increase

but it may also damage the bit or other parts.

4. Change rotation speed

Operate the shift knob to change the rotational

speed. Move the shift knob in the direction of the

arrow (see Figs. 5 and 6).

When the shift knob is set to “L”, the drill rotates

Work Usable range Suggestions

Drilling

Brick: 10 mm

Use for drilling purpose.

Wood: 18 mm

Steel: 10 mm

Aluminum: 10 mm

Driving

Machine screw: 6 mm

Use the bit and socket matching the

screw diameter.

Nut: 5 mm

Wood screw: 5.1 mm (diameter) x 32 mm (length) Use after drilling a pilot hole.

Table 2

6. How to select tightening power and rotational speed

Table 1

Use Cap Position

Rotating speed selection (Position of the shift knob)

L (Low speed) H (High speed)

Driving

Machine screw 1 – 5

or 4 mm or sma

ameter

screws.

or 5 mm or

arger

diameter screws.

Wood screw 1 – 5 For 3.5 mm or smaller nominal

diameter screws.

For 3.8 mm or larger

nominal diameter screws.

Drilling

Brick ––––––

illi

ng w

working drill.

Wood For 10 mm or larger diameters.

or 10 mm or sma

diameters.

Metal

illi

ng w

ron

working drill.

––––––

For drilling with a carbide

tipped drill bit.

For drilling with a metal

working drill bit.

CAUTION

⅜ The selection examples shown in Table 2 should

be considered as general standard. As different types

of tightening screws and different materials to be

tightened are used in actual works proper

adjustments are naturally necessary.

7. Mounting and dismounting of the bit.

(1) Mounting the bit

After inserting a driver bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve

by turning it toward the right (in the clockwise

direction as viewed from the front). (See Fig. 7)

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counter-clockwise

direction as viewed from the front). (See Fig. 7)

CAUTION:

When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit.

Set the clutch mode between 1 and 3 and then turn

the sleeve to the loose side (left side ) while operating

the clutch. It should be easy now to loosen the

sleeve.

8. Confirm that the battery is mounted correctly.

9. Check the rotational direction

The bit rotates klockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn

the bit counterclockwise. (See Fig. 8). (The

and

marks are provided on the body.)

CAUTION:

Always use the impact drill with clockwise rotation,

when using it as an impact drill.

10. Switch operation

When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ THe rotational speed of the drill can be controlled

by varying the amount that the trigger is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV10DVA Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info