Bedienungsanleitung Hitachi DV18DVF (Seite 13 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566559

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

(1) Operating the hook

(a) Pull out the hook toward you in the direction of arrow

(A) and turn in the direction of arrow (B) (Fig. 12).

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position

for

use.

(2) Switching the hook position

CAUTION

Incomplete installation of the hook may result in bodily

injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin (Fig. 13).

(b) Remove the hook and spring (Fig. 14).

hook and spring on the other side and

securely fasten with screw (Fig. 15).

NOTE

Pay attention to the spring orientation. Install the spring

with larger diameter away from you (Fig. 15).

(3) Using the bit holder (Hook with bit holder)

○ Installing the bit

Slide the bit from the side

and then insert ﬁ rmly until

the groove on the bit locks in the protruded section of

the hook.

○ Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb (Fig. 16).

CAUTION

○ Only Hitachi STANDARD ACCESSORIES phillips bit

(No. 2

× 65L; Code No. 983006) may be used. Do not

use other bits since they may come loose.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and cause

possible motor malfunction, sharpen or replace the tool

as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the

screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning

on the outside

When the impact driver drill is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, for they

melt plastics.

5. Storage

Store the impact driver drill in a place in which the

temperature is

less than 40°C and out of reach of

children.

6. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized Service

Center.

This Parts List will be helpful if presented with the tool to

the Hitachi Authorized Service Center when requesting

repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without prior

notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed

(such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or normal

wear and tear. In case of complaint, please send the Power

Tool, undismantled, with the GUARANTEE CERTIFICATE

found at the end of this Handling instruction,

to a Hitachi

Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the speciﬁ cations herein are subject to change

without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 96 dB (A)

Measured A-weighted sound pressure level: 85 dB (A)

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined according

EN60745.

Impact drilling into concrete:

Vibration emission value

ah, ID = 13.5 m/s

Uncertainty K = 2.4 m/s

Drilling into metal:

Vibration emission value

ah, D = 2.4 m/s

Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diﬀ er from the

declared total value depending on

the ways in which the tool is used.

○ To identify safety measures to protect the operator

that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the

tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

000Book_DV14DVF_Tha.indb 13000Book_DV14DVF_Tha.indb 13 2010/04/06 17:39:082010/04/06 17:39:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV18DVF Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info