Bedienungsanleitung Hitachi DV18DVF (Seite 12 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566559

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

6. How to select tightening torque and rotational speed

Table 4

Use

Clutch Dial

Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Driving

Machine screw 1 – 22

For 6 mm or smaller diameter

screws.

For 6 mm or smaller diameter

screws.

Wood screw

1 –

For 6 mm or smaller nominal

diameter screws.

For 3.8 mm or smaller nominal

diameter screws.

Drilling

Brick

For 13 mm or smaller diameters.

For 8 mm or smaller diameters.

(DV14DVF)

For 10 mm or smaller diameters.

(DV18DVF)

Wood

For 32 mm or smaller diameters.

(DV14DVF)

For 18 mm or smaller diameters.

(DV14DVF)

For 38 mm or smaller diameters.

(DV18DVF)

For 22 mm or smaller diameters.

(DV18DVF)

Metal

For drilling with a metal working drill

bit.

CAUTION

○ The selection examples shown in Table 4 should be

considered as general standard. As diﬀ erent types of

tightening screws and diﬀ erent materials to be tightened

are used in actual works proper adjustments are naturally

necessary.

○ When using the impact driver drill with a machine screw

HIGH (high speed), a screw may damage or a bit may

loose due to the tightning torque is too strong. Use the

impact driver drill at LOW (low speed) when using a

machine screw.

NOTE

The use of the battery EB1414S, EB1814SL, BCC1412

and BCC1812 in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns to

normal when the battery warms up.

7. Mounting and dismounting of the bit

(1) After inserting a driver bit, etc. into the keyless drill chuck,

ﬁ rmly grasp the

ring and tighten the sleeve by turning it

toward the right (in the clockwise direction as viewed

from the front) (See Fig. 8).

○ If the sleeve becomes loose during operation, tighten it

further. The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Firmly grasp

the ring and loosen the sleeve by turning

it toward the left (in the counter-clockwise direction as

viewed from the front) (See Fig. 8).

CAUTION

When it is no longer possible to loosen the sleeve, use a

vise or similar instrument to secure the bit. Set the clutch

mode between 1

and 11 and then turn the sleeve to the

loose side (left side) while operating the clutch. It should

be easy now to loosen the sleeve.

8. Conﬁ rm that the battery is mounted correctly

9. Check the rotational direction

The bit rotates clockwise (viewed from the rear side) by

pushing

the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise (See Fig. 9) (The

and marks

are provided on the body).

CAUTION

Always use this unit with clockwise rotation, when using it

as an impact drill.

10. Switch operation

○ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

○ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly and

increases as the trigger switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about to

rotate; This is only a noise, not a machine failure.

11. For

drilling into brick

Excessive pressing force never increases drilling speed.

It will not only damage the drill tip or reduce working

eﬃ ciency, but could also shorten the service life of

drill bit. Operate the impact driver drill within 10-15 kg

pressing force while drilling into brick.

12. Using the

bit holder

CAUTION

○ Stow the bit in the speciﬁ ed location on the tool. If the tool

is used with the bit stowed improperly, the bit may fall and

cause bodily injury.

○ Do not stow bits that are of a diﬀ erent length, gauge or

dimension than the plus driver

bit (65 mm long) included

in the STANDARD ACCESSORIES.

The bit may fall and cause bodily injury.

(1) Removing the bit

Securely hold the main unit and pull out the bit by holding

the tip with your thumb (Fig. 10).

(2) Installing the Bit

Install the bit with steps opposite of

when removing.

Insert the bit so that the right and left sides are equal, as

shown in Fig. 11

13. Using the hook

CAUTION

○ When using the hook, pay suﬃ cient attention so that the

main equipment does not fall. If the tool falls, there is a

risk of accident.

○

Do not attach the tip tool except phillips bit to the tool

main unit when carrying the tool main unit with the hook

suspended from a waist belt.

Injury may result if you carry the equipment suspended

from the waist belt with sharp tipped components such

as drill bit attached.

The

hook can be installed on the right or left side and the

angle can be adjusted in 5 steps between 0° and 80°.

000Book_DV14DVF_Tha.indb 12000Book_DV14DVF_Tha.indb 12 2010/04/06 17:39:082010/04/06 17:39:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV18DVF Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info