Bedienungsanleitung Hitachi fds 10 dv (Seite 28 von 34) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

386508

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the driver drill, charge the battery as

follows.

1. Insert the battery in the charger.

Position the battery so that the nameplate faces

toward the nameplate of the charger and press in

the battery until it comes into contact with the

bottom plate. (See Figs. 1 and 3)

2. Connect the charger power cord to the AC outlet.

Connecting the power cord will turn on t he charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up pull out the

power cord from the AC outlet and check the

battery mounting condition.

About 1 hour is required to fully charge the battery

at a temperature of about 20°C. The pilot lamp goes

off to indicate that the battery is fully charged.

CAUTION

If the battery is heated due to direct sunlight,

etc., just after operation, the charger pilot lamp

may not light. At that time cool the battery first,

then start charging.

3. Disconnect the charger power cord from the AC

outlet.

4. Hold the charger firmly and pull out the battery.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by follow-

ing the precautions.

HOW TO USE

CAUTION:

⅜ Before installing batteries, make sure that the

reversing switch is in neutral position. (See Fig. 4.)

1. Confirm the cap position (see Fig. 5)

The tightening power of this unit can be adjusted

according to the cap position, at which the cap is

set.

(1) For using the unit as a screw driver, set the cap

white line to one of the numerals “1” to “5” on

the outer frame.

(2) For use as a drill, set the white line at the drill mark

“

” (see Fig. 5).

CAUTION

⅜ Set the cap white line at one of either the numerals

or drill marks.

2. Tlightening power adjustment

(1) Tightening power

Tightening power should correspond in its intensity

to the screw diameter. When too strong power is

used, the screw head may be broken or be injured.

Be sure to adjust the cap position according to the

screw diameter.

2. Plus driver bit

Bit No. Screw size

No. 2 3-5 mm

OPTIONAL ACCESSORIES (sold separately)

1. Battery (FEB7)

3. Minus driver bit

a Screw size

0.8 mm 4 mm

5. Drill bit for steel

Diameter, 2 mm, 5 mm, 6 mm.

6. Drill bit for wood

Diameter, 10 mm, 13 mm.

Optional accessories are subject to change without notice.

APPLICATIONS

⅜ Driving and removing of machine screws, wood

screws, tapping screws, etc.

⅜ Drilling of various metals.

⅜ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch

to remove the battery (see Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

4. Hexagon socket (for nuts and bolts)

Socket No. Screw size

74 mm

85 mm

Socket No.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi fds 10 dv Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi fds 10 dv

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info