Bedienungsanleitung Hitachi fds 10 dv (Seite 29 von 34) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

386508

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Driving

Machine screw 1 – 5

For 4 mm or smaller diameter

screws.

For 5 mm or larger diameter

screws.

Wood screw 1 – 5

For 3.5 mm or smaller nominal

diameter screws.

For 3.8 mm or larger nominal

diameter screws.

Drilling

Wood For 10 mm or larger diameters.

For 10 mm or smaller

diameters.

Metal

For drilling with an iron

working drill.

—————

(2) Tightening power indication

Tightening power should be changed according to

the screw type and the materials to be tightened.

Guidance of the tightening power is indicated on

the outer frame of this unit with numerals “1”, “2”,

“3”, “4” and “5”. The minimum power is from “1”

position and bigger the value the stronger is the

power (see Fig. 5).

(3) How to adjusts the tightening power

Rotate the cap and set to one of the numerals.

Adjust the power by cap rotation in such a way that

when the power is too strong, set to the next

smaller numeral and set to the next larger numeral

when too weak.

CAUTION

⅜ The motor rotation may be locked to cease while

the unit is used as drill. While operating the driver

drill, take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Change rotation speed

Operate the shift knob to change the rotational

speed. Move the shift knob in the direction of the

arrow (see Figs. 6 and 7).

When the shift knob is set to “L”, the drill rotates

at a low speed.

When set to “H”, the drill rotates at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “H” (high speed) and

the position of the cap is “4” or “5”, it may happen

that the clutch does not engaged and that the motor

is locked. In suh a case, please set the shift knob

to “L” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt.

4. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown

in Table 1.

Work Usable range Suggestions

Drilling

Wood: 15 mm

Use for drilling purpose.Steel: 10 mm

Aluminum: 10 mm

Driving

Machine screw: 6 mm

Use the bit and socket matching the screw

diameter.

Nut: 5 mm

Wood screw: 5.1 mm (diameter) x 35 mm (length) Use after drilling a preparatory hole.

Table 1

5. How to select tightening power and rotational speed

Table 2

CAUTION

⅜ The selection examples shown in Table 2 should

be considered as general standard. As different types

of tightening screws and different materials to be

tightened are used in actual works proper

adjustments are naturally necessary.

6. Mounting and dismounting of the bit.

(1) After inserting a driver bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve

by turning it toward the right (in the clockwise

direction as viewed from the front). (See Fig. 8)

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counter-clockwise

direction as viewed from the front). (See Fig. 8)

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit.

Set the clutch mode between 1 and 3 and then turn

the sleeve to the loose side (left side) while operating

the clutch. It should be easy now to loosen the

sleeve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi fds 10 dv Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi fds 10 dv

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info