Bedienungsanleitung Hitachi NR90GC (Seite 12 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568885

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

English

CAUTION

⅜ If the gas leaks from the metering valve or the gas

cartridge after attached the metering valve, replace

with the new metering valve.

⅜ Do not attempt to reuse the metering valve.

Replace with the new metering valve.

2. Battery

You must charge the battery before use.

The charging method of battery is shown in page 10.

3. Check on safety

CAUTIONS

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protector.

⅜ Check the retaining screws which fix the top cover,

etc. for tightness.

Check the tool for defective or rusty parts.

⅜ Check whether or not the push lever works correctly

without nails, fuel cell and battery. Also check whether

or not any dirt has adhered to the moving parts of the

push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Insert battery into the tool (See Fig. 4)

Do not operate the push lever or trigger while

installing the battery.

Make sure the battery indicator light is flashing GREEN

(See Fig. 5).

If the battery indicator light is flashing RED, the battery

doesn’t have enough power and it needs to be

charged.

BATTERY INDICATOR LIGHT

– Flashing GREEN: Enough power remaining (The

light turns steady during

operation).

– Flashing RED: Insufficient power remaining (The

light turns steady during operation).

– OFF: The battery is extremely empty. Charge the

battery.

Power saving mode

If the tool has not been used for about an one hour

with the battery still installed, Power saving mode

turns on to minimize unnecessary consumption of

battery power. Power saving mode is also activated

when the battery power is extremely low or there’s

an abnormality in the machine so please pay attention

to the battery indicator light after deactivating Power

saving mode (by removing the battery and reinstall

it).

2. Insert fuel cell into the tool

(1) Pulling the latch and open the cell cover (See Fig. 6).

(2) Insert the fuel cell into the tool (See Fig. 7).

(3) Insert the stem of fuel cell into the hole of adaptor

(See Fig. 8).

(4) Close the cell cover.

3. Load nails

(1) Insert nail strip into rear of magazine (See Fig. 9).

(2) Slide the nail strip forward in the magazine (See Fig. 10).

(3) Pull the nail feeder (B) back to engage the feeder knob

to the nail strip (See Fig. 11).

NOTE

⅜ Use nail strip of more than 10 nails.

The Nailer is now ready to operate.

Removing the nails:

1 Pull the feeder knob backward (See Fig. 12).

2 Return the feeder knob forward quietly while pushing

the nail feeder (B).

3 Pull out nails from the back of the magazine (See Fig.

13).

CAUTION

⅜ To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a

work bench on floor. Also, never face the nail outlet

toward any part of a person.

HOW TO USE THE NAILER

CAUTION

⅜ Never use the top cover or housing of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

⅜ Squeeze the trigger when drive a nail, otherwise the

piston can not return correctly.

⅜ Make sure the nailing depth when the temperature is

above 40°C or below 0°C.

1. Nailing procedures

This power tool is equipped with a FULL SEQUENTIAL

ACTUATION MECHANISM.

(1) Intermittent nailing

Depress the nail outlet onto the desired point; then pull

the trigger to drive a nail in a single shot (See Fig. 14).

After nailing once, nailing will not be possible again

until the trigger is released and pressed again.

(2) Push lever

When depressing the nail outlet, be sure to fully lift

the push lever (See Fig. 14) to release the safety lock.

Thus, nails cannot be driven without releasing the

safety lock even though the trigger is pulled.

The machine employs a preventive mechanism for

unloaded operation.

The machine enters a state where the push lever

cannot be pushed up. This takes place when the

magazine is not loaded with nails or when the

remaining number of nails becomes less than 8 or 9

(NR90GC), 5 or 6 (NR90GR).

CAUTION

⅜ Exercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

⅜ Do not drive a nail on another nail.

⅜ Do not drive a nail on metal parts.

⅜ Use caution not to throw the push lever tip onto wood

when the push lever cannot be pushed up.

NOTE

⅜ Under low temperature conditions, the tool

sometimes does not operate correctly. Always operate

the tool at the appropriate ambient temperature.

2. Adjusting the nailing depth (See Fig. 16, 17)

To assure that each nail penetrates to the same depth,

be sure that the tool is always held firmly against the

workpiece.

If nails are driven too deep or shallow into the

workpiece, adjust the nailing in the following order.

1 Remove the fuel cell and the battery from the tool

(See Fig. 15).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NR90GC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info