Bedienungsanleitung Hitachi NR90GC (Seite 13 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568885

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

English

2 If nails are driven too deep, move the push lever

to forward (See Fig. 16).

If nails are driven too shallow, move the push lever

to backward (See Fig. 17).

3 Stop moving the push lever when a suitable

position is reached for a nailing test.

4 Connect the fuel cell and the battery to the tool.

ALWAYS WEAR EYE PROTECTOR.

Perform a nailing test.

5 Remove the fuel cell and the battery from the tool.

6 Choose a suitable position for the push lever.

3. Clearing a jam

If nails are jammed in firing head, remove it, and adjust

the nailing in the following order.

1 Remove the fuel cell and the battery from the

Nailer. (See Fig.15)

2 Lock follower back in magazine and remove

fasteners.

3 Remove the bolts with wrench. (See Fig.18)

4 Pull magazine away from the firing head, and clear

jam. (See Fig.19)

5 Connect the fuel cell and the battery to the Nailer.

ALWAYS WEAR SAFETY GLASSES.

INSPECTION AND MAINTENANCE

CAUTION

Be sure to remove the battery and fuel cell during

clearing jams, inspection, maintenance and cleaning.

1. Inspecting the magazine

1 DISCONNECT BATTERY and FUEL CELL.

2 Clean the magazine. Remove paper chips or wooden

chips which may have accumulated in the magazine.

Lubricate it with Hitachi gas strip nailer lubricant.

2. Check on mounting screws for each part

At regular intervals check every part for loose mounting

screws. Retighten any loose screws. Operating the

equipment with loose screws untightened will incur

a hazard.

3. Inspecting the push lever

Check if the push lever can slide smoothly.

Clean up the sliding area of the push lever and use the

provided oil for lubrication from time to time.

Lubrication enables smooth sliding and simultaneously

serves to prevent the formation of rust.

4. Storing (See page 8)

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the tool in a warm area.

⅜ When not in use, the tool should be stored in a warm

and dry place.

Keep out of reach of children.

5. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

APPLICABLE LUBRICANTS

Use HITACHI Gas Nailer lubricant.

Do not use detergent oil or additives.

These lubricants will harm the O-rings and other rubber

parts. This will cause the tool malfunction.

Noise Information

Noise characteristic values in accordance with EN 792-

13, JUNE, 2000:

The typical A-weighted single-event sound power level

,1s,d = 108 dB

The typical A-weighted single-event emission sound

pressure level at work station

,1s,d = 99 dB

These values are tool-related characteristic values and

do not represent the noise development at the point of

use. Noise development at the point of use will for

example depend on the working environment, the

workpiece, the workpiece support and the number of

driving operations, etc.

Depending on the conditions at the workplace and the

form of the workpiece, individual noise attenuation

measures may need to be carried out, such as placing

workpieces on sound-damping supports, preventing

workpiece vibration by means of clamping or covering,

etc.

In special cases it is necessary to wear hearing protection

equipment.

Vibration Information

The typical vibration characteristic value in accordance

with EN 792-13, JUNE, 2000: 3.5 m/s

This values is a tool-related characteristic value and does

not represent the influence to the hand-arm-system

when using the tool. An influence to the hand-arm-system

when using the tool will for example depend on the

gripping force, the contact pressure force, the working

direction, the adjustment of energy supply, the workpiece,

the wrokpiece support.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NR90GC Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info