Bedienungsanleitung Hitachi NV90AG (Seite 9 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568916

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

English

NOTE

The air supply hoses must have a minimum working

pressure rating of 12.8 bar (180 psi) or 150 percent of

the maximum pressure produced in the air supply

system, whichever is higher.

2. Check on safety

CAUTIONS

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protector.

⅜ Check the retaining screws which fix the exhaust

cover, etc. for tightness.

Check the nailer for air leaks and defective or rusty

parts.

⅜ Check whether or not the push lever works correctly.

Also check whether or not any dirt has adhered to the

moving parts of the push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Check the air pressure

CAUTION

The air pressure must be constantly maintained at

4.9 – 8.3 bar (70 – 120 psi.).

Adjust the air pressure between 4.9 to 8.3 bar (70 ~

120 psi.) according to the diameters and length of

nails and hardness of the wood being nailed. Pay

special attention to the output pressure, capacity,

and piping on the air compressor, so that air pressure

does not exceed the specified limit. Note that

excessive pressure may affect overall performance,

service life, and safety.

2. Lubrication

(1) Prior to operating this nailer, be sure to provide an air

set between the air compressor and this device.

Lubrication through the air set offers smooth

operation, extended service life, and anticorrosion.

Adjust the oiler so that a single drop of oil is supplied

at intervals of 5 to 10 nailing cycles.

(2) It is recommended using the recommended oil (SHELL

TONNA). Other applicable oils are listed. Never mix

two or more types of different oils.

3. Load Nails

(1) Grip the nail guide and knob with finger.

Press the knob down and swing the nail guide open.

And open the magazine cover (Fig. 2).

(2) Adjust the position of the plate according to the nail

length (Fig. 3).

The nail will not feed smoothly if the plate is not

correctly adjusted (Fig. 4).

Dimensions of nails

STANDARD ACCESSORIES

⅜ Eye protector .............................................................. 1

OPTIONAL ACCESSORY

⅜ Nose cap (Code No. 883-106)

APPLICATIONS

⅜ Floor and wall flaming.

⅜ Subflooring and roof decking.

⅜ Mobile home and modular housing construction.

NOTE

3.3 mm × 90 mm (.131" × 3-1/2") nails cannot be

driven in some cases, depending on the material.

Test drive some of the nails first to check before

using.

PREPARATION PRIOR TO OPERATION

1. Prepare the hose

Be sure to use the hose provided with minimum 8

mm (5/16”) inside diameter.

NAIL SELECTION

Wire collated nails can be driven with this tool.

Choose a suitable nail from Fig. Nails which are not

shown in Fig. can not be driven with this tool. Nails are

linked and rolled.

SPECIFICATIONS

Type of power Piston reciprocating

Air pressure (Gauge) 4.9 – 8.3 bar (70 – 120 psi.)

Applicable nails ref. Fig.

Amount of loadable nails 200 – 300 nails (1 coil)

Size 336 mm (L) × 332 mm (H) × 135 mm (W) (13-1/4” × 13-1/16” × 5-5/16”)

Weight 3.5 kg (7.7 lbs)

Nail-feeding method Piston reciprocation

Hose (inside diam.) 8 mm (5/16”)

Nail

Min. Max.

6 mm

(.236”)

2.5 mm

(.099”)

45 mm (1-3/4”)

90 mm (3-1/2”)

3.3 mm

(.131”)

7.2 mm

(.283”)

01Eng_NV90AG_WE.p65 1/31/13, 14:319

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV90AG Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info