Bedienungsanleitung Hitachi NV90AG (Seite 10 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568916

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

English

a. Turn the nail holder about 90 degrees

counterclockwise.

b. Slide in vertical direction possible.

Lift or lower the nail holder to accept different

length nails.

c. Adjust the plate to the nail length reference points

on the magazine cover and turn the nail holder 90

degrees clockwise until you hear “click”.

(3) Place the nail coil into the magazine.

Uncoil enough nails to reach the driving hole (Fig. 5).

When using wire collated nails

Insert the first nail into the driving hole and the

second nail between the two pawls of the feeder.

Fit the nail head in the guide slot (Fig. 6).

(4) Close the magazine cover first and swing the nail

guide closed (Fig. 7).

(5) Lock the knob correctly.

NOTE

Be careful not to deform the collated wires and not to

disengage the nails with the guide surface.

Otherwise, the nail guide will not close correctly.

CAUTION

To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a

work bench or floor. Also, never face the nail outlet

toward any part of a person.

NOTE

Before loading the nails in the magazine, position the

nail holder according to the length of the nail. If the

nail holder position is not adjusted properly, nail

feed may jam. If the cover is forcibly closed without

adjusting the position of the nail holder, the nail

holder may be damaged.

HOW TO USE THE NAILER

CAUTIONS

⅜ Never use the head or body of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

1. Nailing procedures

This Hitachi nailer is equipped with a nailer operation

switching device.

Use SINGLE SEQUENTIAL ACTUATION MECHANISM

or CONTACT ACTUATION MECHANISM in

accordance with the work to be performed.

(1) Intermittent nailing

Set the switching device to the upward position (to

set to SINGLE SEQUENTIAL ACTUATION

MECHANISM) (See Fig. 8).

Depress the nail outlet onto the desired point; then

pull the trigger to drive a nail in a single shot (See

Fig. 9).

After nailing once, nailing will not be possible again

until the trigger is released and pressed again.

WARNING

A nail will fire each time the trigger is depressed as

long as the push lever remains depressed.

CAUTION

If you do not pull the trigger quickly and crisply while

in the single shot mode, the nailer will bounce and

shoot several nails instead of just one. To avoid this,

be sure to pull the trigger quickly and crisply.

(2) Push lever

When depressing the nail outlet, be sure to fully lift

the push lever (See Fig. 9) to release the safety lock.

Thus, nails cannot be driven without releasing the

safety lock even though the trigger is pulled.

(3) Continuous nailing

Set the switching device to the downward position

(to set to CONTACT ACTUATION MECHANISM) (See

Fig. 10).

First, pull the trigger. Then depress the devise onto

the desired position to automatically drive nails (See

Fig. 11).

The SINGLE SEQUENTIAL ACTUATION MECHANISM is

for use where precision fastener placement is desired.

The SINGLE SEQUENTIAL ACTUATION MECHANISM

may reduce the possibility of bodily injury to you or

others in the work area compared to the CONTACT

ACTUATION MECHANISM. This is because it is less

likely to drive an unwanted nail if you keep the trigger

pulled and accidentally bump the push lever against

yourself or others.

The SINGLE SEQUENTIAL ACTUATION MECHANISM

may also reduce the speed of operation compared to the

CONTACT ACTUATION MECHANISM. The SINGLE

SEQUENTIAL ACTUATION MECHANISM is

recommended to inexperienced users.

CAUTION

⅜ Exercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

⅜ Do not drive a nail on another nail.

⅜ Do not drive a nail on metal parts.

NOTES

⅜ Precautions on no-load operation

Sometimes nailing will continue after driving in all

nails previously contained in the magazine.

This is termed “no-load operation”. Such operation

may deteriorate the damper, magazine, and nail

feeder.

To avoid no-load operation, occasionally confirm the

amount of remaining nails. On the other hand, all

nails should be removed after using this nailer.

⅜ Always handle nails and package carefully. If nails

are dropped, collating bond may be broken.

⅜ After nailing:

(1) disconnect air hose from the nailer;

(2) remove all nails from the nailer;

(3) supply 5 – 10 drops of Hitachi pneumatic tool

lubricant into the air plug on the nailer; and

(4) open the petcock on the air compressor tank to

drain any moisture.

⅜ Under low temperature conditions, the machine

sometimes does not operate correctly. Always operate

the machine at the appropriate ambient temperature.

2. Adjusting the nail-driving depth

CAUTIONS

When making adjustments, be sure remove your

finger from the trigger. When making adjustments,

be sure that the nail outlet is not facing downward

and that body parts or other persons are not in the

path of the nail outlet.

01Eng_NV90AG_WE.p65 1/31/13, 14:3110

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV90AG Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info