Bedienungsanleitung Hitachi RH600T (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

570706

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

STANDARD ACCESSORIES

1 Nozzle (round) ............................................................. 1

2 Nozzle (ﬂ at) ..................................................................1

3 Nozzle (curved surface) ...............................................1

4 Nozzle (glass protector) ...............................................1

5 Scraper (with grip) ........................................................1

6 Case .............................................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

○ Peeling oﬀ paint

○ Softening adhesive

○ Removing putty from window frames

○ Forming resin pipes

○ Welding plastic

○ Heat wrapping using heat-shrink ﬁ lm.

○ Soldering

○ Drying work

○ Defrosting work

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the

power requirements speciﬁ ed on the product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

BASIC FUNCTIONS

1. Switch Operations and Temperature Adjustments

(Fig. 1, 2)

Press the switch upward or downward to enable

continual operations even when your ﬁ nger is removed.

Press the protrusion lightly to return the switch to the

central position and turn oﬀ the power.

The wind temperature and wind volume can be adjusted

in two stages depending on which way the switch is set.

Switch [I] position:

110 V: 250°C (wind volume 0.25 m

)

120 V to 127 V: 350°C (wind volume 0.25 m

)

220 V to 240 V: 350°C (wind volume 0.25 m

)

Switch [II] position:

110 V to 127 V: 500°C (wind volume 0.5 m

)

220 V to 240 V: 600°C (wind volume 0.5 m

)

Press the quick cooling button and press the switch to

blow warm air at approximately 50 degrees Celsius for

each of the switch’s wind volumes.

This is used to quickly cool material that is heat-

warping and to cool the nozzle when it reaches high

temperatures after using the tool.

2. Using the Hook (Fig. 3)

CAUTION

○ When pointing the tool upward to work, make sure that

it is placed on a stable block that does not tilt.

○ Do not hang the tool from your wrist or waist when

moving around with the nozzle still hot.

Support the tool ﬁ rmly when pointing the heat-wind release

nozzle upward.

Also, it is possible to suspend the tool from a wrist, etc.,

with a cord to prevent it from being dropped when working

in high locations, etc.

3. Attaching the Nozzle (Fig. 4)

CAUTION

The nozzle is extremely hot immediately after use, so

do not touch it.

NOTE

Make sure you do not drop the nozzle.

Replace the nozzle for a type that is suited to the job in hand.

Insert the nozzle supplied ﬁ rmly into the hot wind release

nozzle until it can go no further.

4. Temperature Settings

WARNING

○ Do not use the tool in the vicinity of volatile substances

(thinner, gasoline, etc.)

○ Do not bring the hot wind release nozzle in close

contact with your hands or face during use.

The nozzle is extremely hot immediately after use, so

do not touch it.

Set the temperature in consideration of the article to be

heated.

Also, pay attention to the surrounding material that will be

heated at the same time.

First of all, apply the hot wind from a distance while checking

that there are no changes in the article being heated, and

then move it closer until it reaches an appropriate distance.

Heating inﬂ ammable substances

(paper, wood, plastic, etc.)

Set the switch to the [I] position and apply the heat with

the nozzle at least 10cm away from the article being

heated.

Gently move the tip of the nozzle up, down, left and right

to apply the heat.

Applying heat constantly to one location may result in

malformation or the outbreak of smoke.

Heating non-ﬂ ammable substances

(metal, stone, concrete, etc.)

Set the switch to the [I] position, and if there are no

problems, move it to the [II] position.

Apply the heat with the nozzle at least 5cm away from

the article being heated.

Holding the nozzle too close may result in the tool

overheating, leading to malfunctions.

WORK EXAMPLE

CAUTION

Parts of the nozzles supplied are sharp, so use gloves

when removing them from the case and when attaching

or detaching them.

Select the nozzle in consideration of the shape of the

article being heated and the area being heated.

1. Peeling oﬀ paint (Fig. 5)

Use nozzle (ﬂ at) or nozzle (round) to soften the paint

with the hot wind, and then remove it with the scraper

supplied.

Note that heating the paint too much may result in it

scorching and becoming harder, making it diﬃ cult to

scrape oﬀ .

2. Softening adhesive (Fig. 6)

Use nozzle (ﬂ at) or nozzle (round) to soften the surface

and make it easy to peel, and then pull up one of the

edges, blow heat underneath it and gently peel it oﬀ so

that none of the adhesive remains.

000Book_RH600T_WE.indb 7000Book_RH600T_WE.indb 7 2013/10/04 13:41:552013/10/04 13:41:55

Hitachi RH600T Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info