Bedienungsanleitung Hitachi SP18SA (Seite 5 von 22) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

512001

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

English

Voltage (by areas)*

Power Input*

No-load speed

Weight (without cord)

1. Mounting

(1) Attach the washer nut on the rubber pad.

(2) While pushing the lock lever with one hand, lock

the spindle by turning the rubber pad slowly with

the other hand.

Tighten the washer nut by using the supplied

wrench.

(3) Cover the rubber pad with the wool bonnet.

Pull the string of the wool bonnet, let it connect

the rubber pad, and tie the string up. Then, tuck

the knot and the remainder of the string into the

wool bonnet. (See Fig. 2)

CAUTION:

⅜ Improper fitting of the wool bonnet may cause

vibration.

⅜ Confirm that the lock lever is disengaged by pushing

lock lever two or three times before switching the

polisher on.

2. Dismounting

To remove the wool bonnet, follow the above

precedures in reverse.

PRACTICAL POLISHER APPLICATION

1. Curved surface as well as plain one is treated for

finishing. It is recommended to hold the polisher

without pushing on the material, and make the best

of the weight of the machine alone. As the excessive

pressure on the polishing surface will not only bring

unsatisfactory result but also apply overload on the

motor.

2. Depending on the finishing degree of the surface,

use the polishing compound or wax. In order to

attain the maximum polishing effect, first polish the

surface with the fine sand paper using the sander,

than polish it with the polishing compound using

the wool bonnet, and than finish with wax. Apply

a small quantity of the compound and wax to the

surface, and polish with the wool bonnet.

3. Don’t let the cord touch the wool bonnet during

its operation, for the rotating wool bonnet may

catch the cord and get caught it in.

4. Switching on the polisher

Pulling the trigger of switch and push the stopper,

it keeps the switched-on condition and it is

convenient for the continuous operation. When

switched off, the stopper can be disengaged by

means of pulling the trigger again.

5. Precaution after use

Do not lay the polisher down immediately after

using on a place where there are many shavings,

much dirt and dust until it has completely stopped

revolving.

SPECIFICATIONS

(110V, 115V, 120V, 127V, 220V, 230V, 240V)

650 W

2000/min

2.9 kg

*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) 180mm Wool Bonnet ................................................. 1

(2) Rubber Pad ................................................................. 1

(3) Wrench ........................................................................ 1

(4) Side handle ................................................................. 1

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜ Polishing or shining painted metal surfaces, such

as those of automobiles, trains, elevators,

refrigerators, sewing machines, washing machines,

metal appliances, etc.

⅜ Polishing varnished surfaces of wooden furniture,

etc.

⅜ Shining synthetic resin or ebonite products.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

Caution:

Damaged cord must be replaced or repaired.

4. Fixing the side handle

Screw the side handle into the housing.

5. Confirm the lock lever.

Confirm that the lock lever is disengaged by pushing

lock lever two or three times before switching the

power tool on (See Fig. 1).

MOUNTING AND DISMOUNTING THE WOOL

BONNET (Fig. 1)

CAUTION: Be sure to switch OFF and disconnect the

attachment plug from the receptacle to avoid

a serious accident.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi SP18SA Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi SP18SA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info