Bedienungsanleitung Hitachi sv 8 sa (Seite 17 von 21) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

389694

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and bench-

es invite injuries.

2. Consider work area environment. Don’t expose

power tools to rain. Don’t use power tools in

damp or wet locations. Keep work area well lit.

Don’t use tool in presence of flammable liquids

or gases.

Power tools produce sparks during operation.

They also spark when switching ON/OFF. Never

use power tools in dangerous sites containing

lacquer, paint, benzine, thinner, gasoline, gases,

adhesive agents, and other materials which are

combustible or explosive.

3. Guard against electric shock. Prevent body contact

with grounded surfaces. For example; pipes, radia-

tors, ranges, refrigerator enclosures.

4. Keep children away. Do not let visitors contact

tool or extension cord. All visitors should be kept

away from work area.

5. Store idle tools. When not in use, tools should

be stored in dry and high or locked-up place out

of reach of children.

6. Don’t force tool. It will do the job better and safer

at the rate for which it was intended.

7. Use right tool. Don’t force small tool or attach-

ment to do the job of a heavy-duty tool. Don’t

use tool for purpose not intended-for example-

don’t use circular saw for cutting tree limbs or

logs.

8. Dress properly. Do not wear loose clothing or

jewelry. They can be caught in moving parts.

Rubber gloves and non-skid footwear are recom-

mended when working outdoors. Wear protective

hair covering to contain long hair.

9. Use safety glasses. Also use face or dust mask

if cutting operation is dusty.

10. Don’t abuse cord. Never carry tool by cord or yank

it to disconnect from receptacle. Keep cord from

heat, oil and sharp edges.

11. Secure work. Use clamps or a vise to hold work.

It’s safer than using your hand and it frees both

hands to operate tool.

12. Don’t overreach. Keep proper footing and balance

at all times.

13. Maintain tools with care. Keep tools sharp and

clean for better and safer performance. Follow

instructions for lubricating and changing accesso

ries. Inspect tool cords periodically and if dam-

aged, have repaired by authorized service center.

Inspect extension cords periodically and replace

if damaged. Keep handles dry, clean, and free

from oil and grease.

14. Disconnect tools. When not in use, before servic-

ing, and when changing accessories, such as

blades, bits, cutters.

15. Remove adjusting keys and wrenches. Form habit

of checking to see that keys and adjusting wrench-

es are removed from tool before turning it on.

16. Avoid unintentional starting. Don’t carry pluggedin

tool with finger on switch. Be sure switch is off

when plugging in.

17. Outdoor use extension cords. When tool is used

outdoors, use only extension cords intended for

use outdoors and so marked.

18. Stay alert. Watch what you are doing. Use com-

mon sense. Do not operate tool when you are

tired.

19. Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will

operate properly and perform its intended func-

tion. Check for alignment of moving parts, binding

of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation.

A guard or other part that is damaged should be

properly repaired or replaced by an authorized

service center unless otherwise indicated else

where in this handling instructions manual. Have

defective switches replaced by authorized service

center. Do not use tool if switch does not turn

it on and off.

20. Do not use power tools for applications other than

those specified in the Handling Instructions.

21. To ensure the designed operational integrity of

power tools, do not remove installed covers or

screws.

22. Do not touch movable parts or accessories unless

the power source has been disconnected.

23. Use your tool at lower input than specified on the

nameplate; otherwise, the finish may be spoiled

and working efficiency reduced due to motor

overload.

24. Do not wipe plastic parts with solvent. Solvents

such as gasoline, thinner, benzine, carbon tetra-

chloride, alcohol, ammonia and oil containing

chloric annex may damage and crack plastic parts.

Do not wipe them with such solvent. Wipe plastic

parts with a soft cloth lightly dampened with

soapy water.

25. Consult an authorized Service Agent in the event

of power tool failure.

26. Use only genuine HITACHI replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi sv 8 sa Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi sv 8 sa

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info