Bedienungsanleitung Hitachi TCG24ECP (Seite 8 von 288) (Alle Sprachen)

661495

Zoom out

Zoom in

Vorherige Seite

1/288

Nächste Seite

English

WA, Ra(G)



Guaranteed sound power level LwA by 2000/14/

Racing

hv, eq(R)

Vibration level by ISO 22867

Rear or Right handle / Equivalent*

hv, eq(F)

Vibration level by ISO 22867

Front or Left handle / Equivalent*



Uncertainty

Before using your machine

• Read the manual carefully.

• Check that the cutting equipment is correctly assembled and adjusted.

• Start the unit and check the carburetor adjustment. See “MAINTENANCE”.

NOTE: Equivalent noise level / vibration level are calculated as the time-weighted energy total for noise / vibration levels

under various working conditions with the following time distribution:

* 1/2 Idle, 1/2 racing.

WHAT IS WHAT? (Fig. 1)

Since this manual covers several models, there may be

some diﬀ erence between pictures and your unit. Use the

instructions that apply to your unit.

A: Fuel cap

B: Throttle trigger

C: Starter handle

D: Cutting attachment guard

E: Cutting attachment

F: Drive shaft tube

G: Handle

H: Hanger

I: Ignition switch

J: Harness (if so equipped)

K: Throttle trigger lockout

L: Choke lever

M: Engine

N: Gear case

O: Combi box spanner

P: Handling instructions

Q: Goggles

R: Hex bar wrench

S: Blade cover (if so equipped)

WARNINGS AND SAFETY

INSTRUCTIONS

Pay special attention to statements preceded by the

following words:

WARNING

Indicates a strong possibility of severe personal injury or

loss of life, if instructions are not followed.

CAUTION

Indicates a possibility of personal injury or equipment

damage, if instructions are not followed.

NOTE

Helpful information for correct function and use.

Operator safety

○ Wear head protection (1). (Fig. 2)

○ Always wear a safety face shield or goggles (2). (Fig. 2)

○ Wear approved hearing protection (3). (Fig. 2)

Long-term exposure to noise can result in permanent

hearing impairment.

Pay attention to your surroundings. Be aware of any

bystanders who may be signaling a problem.

Remove safety equipment immediately upon shutting oﬀ

engine.

○ Always wear heavy, long-sleeved shirts (4) and long

pants (5) and non-slip boots (6) and gloves (7). (Fig. 2)

Do not wear loose clothing, jewelry, short pants, sandals

or go barefoot.

Secure hair so it is above shoulder length.

○ Do not operate this tool when you are tired, ill or under

the inﬂ uence of alcohol, drugs or medication.

○ Do not operate the tool at night or under bad weather

conditions when visibility is poor. And do not operate the

tool when it is raining or right after it has been raining.

Working on slippery ground could lead to an accident if

you lose your balance.

○ Never let a child or inexperienced person operate the

machine.

○ Do not start the engine if there are any ﬂ ammables such

as dry leaves, waste paper or fuel in the vicinity.

○ Never start or run the engine inside a closed room or

building. Breathing exhaust fumes can kill.

○ Keep handles free of oil and fuel.

○ Keep hands away from cutting equipment.

○ Do not grab or hold the unit by the cutting equipment.

○ Gloves should be worn when installing or removing the

cutting attachment. Failure to do so may result in injury.

○ When the unit is shut oﬀ , make sure the cutting

attachment has stopped before the unit is set down.

○ When operation is prolonged, take a break periodically

so that you may avoid possible Hand-Arm Vibration

Syndrome (HAVS) which is caused by vibration.

WARNING

○ Always operate the tool with proper protective equipment

and clothing. Failure to do so may result in accidents

such as burns or injuries. (Fig. 2)

○ Do not touch the spark plug area or high voltage during

operation. Doing so may result in electric shock.

○ Do not allow children near the tool during operation.

○ Do not touch the engine, muﬄ er cover or exhaust vent

during or shortly after operation. Doing so may result in

burn or injury.

○ Antivibration systems do not guarantee that you will

not sustain Hand-Arm Vibration Syndrome or carpal

tunnel syndrome. Therefore, continual and regular users

should monitor closely the condition of their hands and

ﬁ ngers. If any of the above symptoms appear, seek

medical advice immediately.

○ If you are using any medical electric/electronic devices

such as a pacemaker, consult your physician as well as

the device manufacturer prior to operating any power

equipment.

Unit/machine safety

○ Inspect the entire unit/machine before each use.

Replace damaged parts. Check for fuel leaks and make

sure all fasteners are in place and securely tightened.

○ Replace parts that are cracked, chipped or damaged in

any way before using the unit/machine. Faulty parts may

increase the risk of accidents and may lead to an injury.

○ Make sure the cutting attachment guard and harness are

properly attached. Do not operate if cutting attachment

guard and harness is not properly attached.

○ Keep others away when making carburetor adjustments.

000Book_TCG24ECP(S).indb 8000Book_TCG24ECP(S).indb 8 2017/03/24 10:10:482017/03/24 10:10:48

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi TCG24ECP Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info