Bedienungsanleitung Hitachi UG50Y (Seite 14 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571421

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English

Examples of measuring using diﬀ erent reference points

Measuring using front reference point (Fig. 7)

Place the front (reference point) of the instrument against the

measuring surface.

Measuring using rear reference point (Fig. 8)

Place the rear (reference point) of the instrument against the

measuring surface.

Measuring using the W1/4 socket hole (for the tripod) as the

reference point (Fig. 9)

Use the center of the socket hole for attaching the tripod as the

reference point.

NOTE

If the instrument needs to be level with the target, adjust the level using

the bubble tube. (Fig. 10)

5. Measuring procedures in each mode

NOTE

○

Check that there is nothing obstructing measurement by the laser.

○

Do not move the instrument during measuring (except during

continuous measurement).

○

The center of the laser beam is measured. The same applies when

the beam is aimed diagonally at the target.

○

The measuring range may vary depending on the characteristics of

the laser beam reﬂ ected from the target surface or the surrounding

brightness.

To measure quickly and accurately outdoors in bright sunlight, use

a target plate (sold separately) or put the target in the shade.

○

Measuring errors may occur with transparent surfaces (such as

glass or water) or mirror surfaces, as well as in the case of surfaces

with holes in, uneven surfaces, diﬀ erent temperatures and indirectly

reﬂ ected light.

○

If the power is turned on and no button is pressed, the power will

turn oﬀ automatically after approximately 3 minutes. Press the

power button again to resume operation.

○

If the instrument is used and then left with no button pressed,

the laser will turn oﬀ after approximately 30 seconds. Press the

measure button again to resume operation.

○

The length of time after the power is turned on until the instrument is

ready to measure may vary depending on the usage environment.

○

If an error occurs while measuring, remedy the cause before

resuming measuring.

Measuring distance (Fig. 2, 6)

Select distance mode. (See “Selecting a measuring mode”)

Press the measure button and aim the laser beam at the target. The

status is indicated on the display.

Press the measure button again to stop measuring. A beep sounds

and the measurement is indicated on the display. When measuring

is ﬁ nished, the laser goes oﬀ .

To continue measuring distance, repeat steps

and

The side button on the side of the instrument has the same function

as the measure button on the operation panel.

For convenient operation in narrow spaces, the instrument can be

placed in a vertical position.

Continuous measurement

Use continuous measurement to set the desired position from the

target.

Select continuous measurement mode. (See “Selecting a

measuring mode”)

Press the measure button and aim the laser beam at the target.

Move the instrument until the desired measurement is indicated on

the display.

Press the measure button again to ﬁ nish continuous measurement.

The last measurement is indicated on the display.

Measurements are successively indicated on the display with a beep

sound every 0.5 to 3 seconds.

The previous measurement is deleted when the next measurement is

taken.

In continuous measurement mode, the power does not turn oﬀ

automatically. Be sure to press the power button after operation to end

continuous measurement.

000Book_UG50Y_WE.indb 13000Book_UG50Y_WE.indb 13 2009/08/20 13:48:092009/08/20 13:48:09

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi UG50Y Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info