Bedienungsanleitung Hitachi W4YD (Seite 8 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571644

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

English

PRECAUTIONS ON USING AUTOMATIC

SCREWDRIVER

1. This automatic screwdriver is designed for

tightening and loosening screws. Use it only for

these operation.

2. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

3. Use original bits specifically for the automatic

screwdriver.

Use no bits other than the original bits specifically

for the automatic screwdriver. Use of any other

bit can result in screws sticking out and screw

feed malfunctioning.

4. After installing the driver bit, pull lightly out the

bit to make sure that it does not come loose. If

the bit is not installed properly, it can come loose

during use, which can be dangerous.

5. Screw in screws with the main unit held straight.

If the driver is slanted relative to the screw, the

screw head can be damaged and the bit worn.

Moreover, the prescribed torque is not transmitted

to the screw, resulting in screws left sticking out.

STANDARD ACCESSORIES

(1) Screw feed attachment .......................................... 1

(Assembled in main body)

(2) No. 2 Plus Bit .......................................................... 1

(Assembled in main body)

(3) Hook ........................................................................... 1

(4) Sheet .......................................................................... 2

(5) Rubber cover ............................................................ 1

(6) Plastic case ............................................................... 1

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜ Screw driving into indoor gypsum board.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

Place the drive straight against the screw and

screw in.

6. Use the prescribed screws.

Do not use any other screws. They can cause

abnormal work (screws fallen over or sticking out)

and break downs (screw jamming and bit wear).

7. Protect your eyes with protective glasses.

Always wear protective glasses while working.

Drilling scatters plaster powder and tape dust,

which are dangerous if they get into your eyes

8. Watch out for wires and pipes in walls and ceilings.

When working on floors, walls, or ceilings, check

for wires and pipes ahead of time. Work carefully

to avoid shocks and explosions.

9. When the screw feed attachment is removed,

always use the correct driver bit for the screw size.

10. When the screw feed attachment is removed, if

the screwdriver is positioned at an angle against

the tightening screw, the head of the screw may

be damaged or the fixed tightening force will not

transfer to the screw. Always position the

tightening screw and the screwdriver at a straight

angle and then tighten the screw.

SPECIFICATIONS

* Be sure to check the nameplate on product as it is subject to change by areas.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operation immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

5. Preparing the screws

Select screws appropriate to the application.

6. Bit checking and replacement

A No. 2 Plus bit is installed on this machine as a

standard accessory. Always inspect the bit to make

sure it is not damaged. Using worn bits can cause

screw-in malfunctions. Inspect the bit before work

and quickly replace it with a new one when it starts

to wear out. When the bit must be replaced due

to bit damage or any other reason, replace it

according to the instructions in Bit installation and

removal.

Voltage (by areas)* (230 V, 240 V)

Power input 470 W

No-load speed 4700 min

–1

Capacity

Screw size 4 mm

Screw length 25 – 41 mm

Bit shank size 6.35 mm Hex.

Weight (without cord) 1.7 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi W4YD Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info