Bedienungsanleitung Hitachi W4YD (Seite 10 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571644

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

English

Do not drive screws while the slider case is in contact

with the wall. Damaging the screw head causes bit

wear. The proper tightening torque is not transmitted

to the screw if the screw head or bit is worn. This

might also cause the screw not to seat properly and

might cause this unit to break.

3. Using the hook

The hook can be installed on the right or left side and

the angle can be adjusted in 5 steps between 0° and

80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction of

arrow (A) and turn in the direction of arrow (B)

(Fig. 10).

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position

for use.

(2) Switching the hook position

CAUTION

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin (Fig.

11).

(b) Remove the hook and spring (Fig. 12).

securely fasten with screw (Fig. 13).

NOTE

Pay attention to the spring orientation. Install the

spring with larger diameter away from you (Fig. 13).

4. Attaching the rubber cover (Fig. 14)

If concerned about wind coming in from the air vents,

install the accessory rubber cover over the holes to

change the direction of air flow.

To install the cover, press the protrusions firmly into

the air vents. To install easily, press inwards, in order

from the sides.

5. When the slider won’t move smoothly

If the slider will not move smoothly, try cleaning the

sliding surfaces of the slider and slider case with an

air gun, etc. (Fig. 15).

NOTE

⅜ The unit tends to easily become covered with lath or

plaster board dust during jobs where it faces upwards.

Clean the sliding surfaces at regular periods during

the work task.

6. Attaching the sheet

If the sheet has been damaged and cannot be used,

please replace the sheet with attached one. Attach

the sheet by inserting the holes on the sheet on the

two protrusions on the stopper (Fig. 16).

SCREW HANDLING

NOTE

Handle both the packed box of screws and the collated

screw strips with care. If you drop them, screws can

come out of the collated tape and cause screw feed

malfunctions. Do not expose the screws to prolonged

periods of direct sunlight or outside air. They can cause

rust and collated tape problems, so when you will not

be using the screws for awhile, put them in the screw

packing box or the like.

MAINTENANCE AND INSPECTION

1. Inspecting the driver bit

Using a broken bit or one with a worn out tip is

dangerous because the bit can slip. Replace it by

a new one.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so may result in serious hazard.

3. Inspecting the carbon brushes (Fig. 19)

The motor employs carbon brushes which are

consumable parts.

Since an excessively worn carbon brush can result

in motor trouble, replace the carbon brush with a

new one having the same carbon brush No. shown

in the figure, when it becomes worn to or near the

“wear limit”. In addition, always keep carbon brushes

clean and ensure that they slide freely within the

brush holders.

4. Replacing carbon brushes

Disassemble the brush caps with a slotted-head

screwdriver. The carbon brushes can then be easily

removed.

5. Maintenance of the motor

The motor unit winding is the very ”heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

6. Cleaning of the outside

When the automatic screwdriver is stained, wipe

with a soft dry cloth or a cloth moistened with

soapy water. Do not use chloric solvents, gasoline

or paint thinner, as they melt plastics.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi W4YD Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info