Bedienungsanleitung Hitachi WF4V (Seite 7 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571648

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

7. Protect your eyes with protective glasses.

Always wear protective glasses while working.

Drilling scatters plaster powder and tape dust,

which are dangerous if they get into your eyes

8. Watch out for wires and pipes in walls and ceilings.

When working on floors, walls, or ceilings, check

for wires and pipes ahead of time. Work carefully

to avoid shocks and explosions.

9. When the screw feed attachment is removed,

always use the correct driver bit for the screw size.

STANDARD ACCESSORIES

(1) Screw feed attachment .......................................... 1

(Assembled in main body)

(2) No. 2 Plus Bit .......................................................... 1

(Assembled in main body)

(3) Hook ........................................................................... 1

(4) Belt guide ................................................................. 1

(5) Rubber cover (B) ...................................................... 1

(6) Plastic case ............................................................... 1

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜ Screw driving into indoor gypsum board

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operation immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

10. When the screw feed attachment is removed, if

the screwdriver is positioned at an angle against

the tightening screw, the head of the screw may

be damaged or the fixed tightening force will not

transfer to the screw. Always position the

tightening screw and the screwdriver at a straight

angle and then tighten the screw.

SPECIFICATIONS

* Be sure to check the nameplate on product as it is subject to change by areas.

4. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

5. Preparing the screws

Select screws appropriate to the application.

6. Bit checking and replacement

A No. 2 Plus bit is installed on this machine as a

standard accessory. Always inspect the bit to make

sure it is not damaged. Using worn bits can cause

screw-in malfunctions. Inspect the bit before work

and quickly replace it with a new one when it starts

to wear out. When the bit must be replaced due

to bit damage or any other reason, replace it

according to the instructions in Bit installation and

removal.

SCREW FEED ATTACHMENT INSTALLATION

AND REMOVAL

CAUTION

To prevent accidents, always switch off the switch and

unplug the power cord from the electrical socket before

installation or removing screw feed attachment.

1. Screw feed attachment removal

Secure the main body with one hand and turn the

screw feed attachment with another hand in the

direction of the arrow mark shown in Fig. 1.

Align the “

” mark of the main body and the

“

”mark of the screw feed attachment, then pull

the attachment in the direction of the arrow mark

shown in Fig. 2 to remove it.

NOTE

If the dust from the plaster adheres to the attachment

installation gate, it makes the attachment difficult

to remove. Clean the installation gate so the plaster

dust does not adhere.

Voltage (by areas)* (220V, 230V, 240V)

Power input 300 W

No-load speed 0 – 2300/min

Capacity

Screw size 4 mm

Screw length 25 – 41 mm

Tightening torque Maximum 1000 kg-cm

Tightening is M12 high tension bolt (strength grade 12.9).

Tightening time: 3 sec. Use hexagonal socket.

Bit shank size 6.35 mm Hex.

Weight (without cord) 1.8 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WF4V Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info