Bedienungsanleitung Hitachi WF4V (Seite 8 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571648

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

2. Screw feed attachment installation

Perform the installation procedures in the reverse

sequence of the removal procedures.

Position the screw feed attachment over the main

body and align the “

” mark of the main body

and the “

”mark of the screw feed attachment

then turn the attachment in the direction of the

“

”mark shown in Fig. 2 to fix it.

3. Driver bit installation and removal

Collate screw tightening cannot be performed except

by the genuine driver bits for Model WF4V.

Install the bit securely by the following procedures.

Move the guide sleeve to the top edge, insert the

bit into the hexagonal hole of the anvil and then

release the guide sleeve. (Fig. 3)

When removing the bit, perform the installation

procedures in the reverse order.

CAUTION

If the guide sleeve does not return to its original

position, then the driver bit is not installed properly.

HOOK INSTALLATION

(1) Insert the hook into the “A” section of the main

body then turn it clockwise to set the clearance

between the housing and hook to the appropriate

position.

Tighten the nut clockwise to fix the hook securely.

(Fig. 4)

(2) The hook can be hung on your belt or on a pipe

with a diameter of up to 32 mm.

BELT GUIDE INSTALLATION AND REMOVAL

(1) To use as an impact driver, remove the belt guide

by grasping it with the thumb and forefinger and

pulling it in the direction indicated by the arrow

(Fig. 5).

(2) When attaching the belt guide, align point B of the

guide with point C of the housing and press in the

direction indicated by the arrow until the belt guide

clicks into place. (Fig. 6)

RUBBER COVER (B) INSTALLATION

If it is necessary to block the air coming out from one

of the air openings, block the air opening by using the

rubber cover (B) provided. Press the protruding part

of the cover firmly into the air opening, pressing evenly

around the edge, to insert it with the least effort.

(Fig. 7)

NOTE:

When the rubber cover (B) has been used to close the

air opening on one side, the air opening on the opposite

side must be left completely open and unobstructed.

If this is not done, there is a danger that the motor

may burn out.

SCREW LENGTH AND SCREW-IN DEPTH

ADJUSTMENT

The tightening depth of this machine can be adjusted

by rotating the knob.

The tightening depth is adjusted by rotating the knob

and setting the stopper to the numerals (screw length)

indicated on the slider case.

Select a top adjuster to match screw length to be used

and attach it to the top edge. (Refer to Fig. 9, 10)

Store the top adjuster in the storage room on the side

face of the slider case when it is not used.

The top adjuster is stored easily when the button

shown in Fig. 8 is pressed.

(1) In case that you use a screw which has a length

of 25 – 32 mm (L), please use the top adjuster No.

1 (small). (Fig. 9)

Match the stopper to the screw length (25 – 32).

(2) In case that you use a screw which has a length

of 35 – 41 mm (L), please use the top adjuster No.

2 (large). (Fig. 10)

Match the stopper to the screw length (35 – 41).

[Fine adjustment of tightening depth]

The tightening depth adjustments (1) to (2)

mentioned above are just preliminary.

Perform fine adjustment after trial driving.

Rotate the knob in

direction when the screw

head is too high.

Rotate the knob in

direction when the screw

head is too low.

(Refer to Fig. 11)

COLLATED SCREW STRIPS INSTALLATION

AND REMOVAL

1. Installation

(1) Insert the tape tip of collated screw strips into the

belt guide groove (D section).

(2) Next, insert the tape tip into the slider groove (E

section) and feed to push in the \ direction.

(Fig. 12 and Fig. 14)

(3) Set the collated tape so that the first screw is lined

up with the slider screw mark. (Fig. 13 and Fig. 14).

NOTE:

If the tape is not set as shown in the figure, the

bit can damage the board surface (inadequate feed)

and screws can be wasted (excess feed).

2. Removal

When the screws on the tape run out or to remove

a half used belt of screws, pull the tape out in the

\ direction as shown in Fig. 15.

HOW TO USE THE AUTOMATIC

SCREWDRIVER

1. Operations

When you pull the switch and press the driver

straight against the workpiece in continuous

operation mode, the screw is fed and screwed in

automatically. (Fig. 16)

2. Tightening at a corner and adjustment operation

When the screw is tightenined, retightened or

removed in a location where the tightening is

impossible if the screw feed attachment is installed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WF4V Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info