Bedienungsanleitung Honda GP200 (Seite 12 von 96) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

580730

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

12 ENGLISH

Draining the Fuel Tank and Carburetor

1. Move the fuel valve lever to the OFF position (see page 5).

2. Place an approved gasoline container below the carburetor, and

use a funnel to avoid spilling fuel.

3. Move the fuel valve lever to the ON position and loosen the

carburetor drain bolt by turning 1 to 2 turns counter clockwise.

4. After all fuel has drained, tighten the carburetor drain bolt

securely, move the fuel valve to the OFF position.

Engine Oil

1. Change the engine oil (see page 8).

2. Remove the spark plug (see page 11).

3. Pour a teaspoon 5–10 cm

of clean engine oil into the cylinder.

4. Pull the starter grip several times to distribute the oil in the

cylinder.

5. Reinstall the spark plug.

6. Pull the starter grip slowly until resistance is felt and the notch

on the starter pulley aligns with the hole at the top of the recoil

starter cover. This will close the valves so moisture cannot

enter the engine cylinder. Return the starter grip gently.

7. Cover the engine to keep out dust.

Gasoline is highly flammable and explosive, and you

can be burned or seriously injured when handling fuel.

• Stop the engine and keep heat, sparks, and flame

away.

• Handle fuel only outdoors.

• Wipe up spills immediately.

CARBURETOR DRAIN BOLT

GASKET

Storage Precautions

If your engine will be stored with gasoline in the fuel tank and

carburetor, it is important to reduce the hazard of gasoline vapor

ignition. Select a well ventilated storage area away from any

appliance that operates with a flame, such as a furnace, water

heater, or clothes dryer. Also avoid any area with a

spark-producing electric motor, or where power tools are operated.

If possible, avoid storage areas with high humidity, because that

promotes rust and corrosion.

Keep the engine level in storage. Tilting can cause fuel or oil

leakage.

With the engine and exhaust system cool, cover the engine to keep

out dust. A hot engine and exhaust system can ignite or melt some

materials. Do not use sheet plastic as a dust cover.

A nonporous cover will trap moisture around the engine, promoting

rust and corrosion.

Removal from Storage

Check your engine as described in the

BEFORE OPERATION

CHECKS

section of this manual (see page 3).

If the fuel was drained during storage preparation, fill the tank with

fresh gasoline. If you keep a container of gasoline for refueling, be

sure it contains only fresh gasoline. Gasoline oxidizes and

deteriorates over time, causing hard starting.

If the cylinder was coated with oil during storage preparation, the

engine will smoke briefly at startup. This is normal.

TRANSPORTING

If the engine has been running, allow it to cool for at least 15

minutes before loading the engine-powered equipment on the

transport vehicle. A hot engine and exhaust system can burn you

and can ignite some materials.

Keep the engine level when transporting to reduce the possibility of

fuel leakage. Turn the fuel valve lever to the OFF position (see page

5).

5='.IP࣮࣌ࢪᜠ᜞ᜟᜢᖺᜣ᭶ᜠᜡ᪥ࠉฐ᭙᪥ࠉ༗ᚋᜡ᫬ᜡᜢศ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda GP200 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info