Bedienungsanleitung Honda Honda Engines GS190 (Seite 5 von 40) (Englisch, Französisch, Spanisch)

13077

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

Review the instructions provided with the equipment powered by

this engine for any precautions and procedures that should be

followed before engine startup.

OPERATION

SAFE OPERATING PRECAUTIONS

Before operating the engine for the first time, please review the

SAFETY MESSAGES and the BEFORE OPERATION CHECKS

page 4.

For your safety, do not operate the engine in an enclosed area such

as a garage. Your engine's exhaust contains poisonous carbon

monoxide gas that can collect rapidly in an enclosed area and cause

illness or death.

Review the instructions provided with the equipment powered by this

engine for any safety precautions that should be observed with

engine startup, shutdown, or operation.

Do not operate the engine on slopes greater than 20°.

FREQUENCY OF USE

If your equipment will be used on an infrequent or intermittent basis

(more than 4 weeks between usage), refer to the Fuel section of the

STORAGE chapter (page 8) for additional information regarding fuel

deterioration.

STARTING/STOPPING THE ENGINE (ALL TYPES)

See the figures on the top of page 2 to identify the type of control used

on your equipment. Type specific starting and stopping information

can be found after the general information shown below.

• Manual choke: Place the choke lever/rod [1] in the CHOKE

position when starting a cold engine.

Move the choke lever/rod to the OFF position as soon as the

engine fully warms up and runs smoothly without use of the choke,

or for restarting a warm engine.

• Engine speed: For best engine performance, it is recommended

the engine be operated with the throttle in the FAST (or high)

position.

• Starter grip: Pull the starter grip lightly until resistance is felt, and

then pull briskly.

NOTICE

Do not allow the starter grip to snap back against the engine.

Return it gently to prevent damage to the starter.

OIL ALERT

SYSTEM (APPLICABLE ENGINE TYPES)

The Oil Alert system is designed to prevent engine damage caused

by an insufficient amount of oil in the crankcase. Before the oil level in

the crankcase can fall below a safe limit, the Oil Alert system will

automatically stop the engine [the throttle lever (ignition switch lever)

will remain in a run position].

If the engine stops and will not restart, check the engine oil level

(page 7) before troubleshooting in other areas.

Type 1: Manual Choke, Manual Throttle

STARTING THE ENGINE

1. Move the choke rod [1] to the CLOSED position (cold engine)

(see Figure 1, page 2).

2. Move the throttle lever (gray) [2] to the SLOW position, about 1/3

of the way toward the FAST position (see Figure 2, page 2).

Some engine applications use a remotely-mounted throttle control

rather than the engine-mounted throttle lever shown.

3. Pull the starter grip lightly until resistance is felt; then pull briskly.

4. If the choke rod was pulled to the CLOSED position to start the

engine, push it to the OPEN position as soon as the engine warms

up enough to run smoothly.

5. Position the throttle control lever (gray) for the desired engine

speed.

STOPPING THE ENGINE

1. Move the throttle control lever (gray) to the SLOW position.

2. Allow the engine to idle for a few seconds; then move the throttle

control lever to the STOP position.

Type 2: Manual Choke, Ignition Switch Lever,

Fixed Throttle

STARTING THE ENGINE

1. Move the choke rod [1] to the CLOSED position (cold engine)

(see Figure 1, page 2).

2. Move the ignition switch lever (red) [4] to the ON position (see

Figure 4, page 2).

Some engine applications use a remote-mounted ignition switch

rather than the engine-mounted lever shown.

3. Pull the starter grip lightly until resistance is felt; then pull briskly.

4. If the choke rod was pulled to the CLOSED position to start the

engine, push it to the OPEN position as soon as the engine warms

up enough to run smoothly.

The engine speed is preset on this type.

STOPPING THE ENGINE

Move the ignition switch lever (red) to the OFF position

(see Figure 5, page 2).

Type 3: Manual Choke, Engine Stop Switch, Fixed Throttle

Some engine applications use a remote-mounted engine stop

switch rather than the engine-mounted engine stop switch shown.

Refer to the instructions provided by the equipment manufacturer.

STARTING THE ENGINE

1. Move the choke rod [1] to the CLOSED position (cold engine)

(see Figure 1, page 2).

2. Move the engine stop switch [2] to the ON position (see Figure 6,

page 2).

3. Pull the starter grip lightly until resistance is felt; then pull briskly.

4. If the choke rod was pulled to the CLOSED position to start the

engine, push it to the OPEN position as soon as the engine warms

up enough to run smoothly.

The engine speed is preset on this type.

STOPPING THE ENGINE

Move the engine stop switch to the OFF position (see Figure 6,

page 2).

 WARNING

Exhaust contains poisonous carbon monoxide gas that can build

up to dangerous levels in closed areas. Breathing carbon

monoxide can cause unconsciousness or death.

Never run the engine in a closed or even partially closed area

where people may be present.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GS190 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GS190

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info