Bedienungsanleitung Honda Honda Engines GS190 (Seite 7 von 40) (Englisch, Französisch, Spanisch)

13077

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

Never use stale or contaminated gasoline or oil/gasoline mixture.

Avoid getting dirt or water in the fuel tank.

Adding Fuel

See Figure 7, page 3.

1. Remove the fuel tank cap.

2. Add fuel to the bottom of the fuel level limit [1] in the neck of the

fuel tank. Do not overfill. Wipe up spilled fuel before starting the

engine.

3. Install the fuel tank cap and tighten it until it clicks.

Move at least 10 feet (3 meters) away from the fueling source and

site before starting the engine.

NOTICE

Fuel can damage paint and some types of plastic. Be careful not to

spill fuel when filling your fuel tank. Damage caused by spilled fuel is

not covered under your Distributor’s Limited Warranty.

Fuel Storage Container

Store your gasoline in a clean, plastic, sealed container designed for

fuel storage. Close the vent (if equipped) when not in use, and store

the container away from direct sunlight. If it takes more than 3 months

to use the fuel in the container, we suggest adding a fuel stabilizer to

the fuel when you fill the container. If you have some fuel left in the

storage container at the end of the season, the Environmental

Protection Agency (EPA) suggests adding the gasoline to your

vehicle’s gas tank (http://epa.gov/reg5oair/mobile/winter.html).

ENGINE OIL

Oil is a major factor affecting performance and service life. Always

change the oil in accordance with the maintenance schedule

(page 6).

Recommended Oil

See Figure 8, page 3.

Use 4-stroke motor oil that meets or exceeds the requirements for API

service category SJ or later. Always check the API service label on

the oil container to be sure it includes the letters SJ or later.

SAE 10W-30 is recommended for general use. Other viscosities

shown in the chart may be used when the average temperature in

your area is within the indicated range.

Oil Level Check

See Figure 8, page 3.

1. Check the oil with the engine stopped and level.

2. Remove the oil filler cap/dipstick [1] and wipe it clean.

3. Insert the oil filler cap/dipstick into the oil filler neck as shown, but

do not screw it in, and then remove it to check the oil level.

4. If the oil level is near or below the lower limit mark [2] on the

dipstick, fill with the recommended oil to the upper limit mark [3].

Do not overfill.

5. Reinstall the oil filler cap/dipstick [1].

Oil Change

See Figure 9, page 3.

Drain the engine oil when the engine is warm. Warm oil drains quickly

and completely.

1. Place a suitable container next to the engine to catch the used oil.

2. Remove the oil filler cap/dipstick [1], and the oil drain plug [2] and

washer [3].

3. Allow the used oil to drain completely; then reinstall the drain plug

and new washer. Tighten the drain plug securely.

Please dispose of used motor oil in a manner that is compatible

with the environment. We suggest you take used oil in a sealed

container to your local recycling center or service station for

reclamation. Do not throw it in the trash, pour it on the ground, or

pour it down a drain.

4. With the engine in a level position, fill to the upper limit mark

(bottom edge of the oil fill hole) on the dipstick with the

recommended oil. Do not overfill.

Capacity: 20 oz (0.58 L)

NOTICE

Running the engine with a low oil level can cause engine damage.

This type of damage is not covered by the Distributor’s Limited

Warranty.

5. Reinstall the oil filler cap/dipstick [1] securely.

AIR CLEANER

A properly maintained air filter will help prevent dirt from entering your

engine. Dirt entering the carburetor can be drawn into small passages

in the carburetor and cause premature engine wear. These small

passages can become blocked, causing starting or running problems.

You will need to clean the filter more frequently if you operate the

engine in very dusty areas.

NOTICE

Operating the engine without an air filter, or with a damaged filter, will

allow dirt to enter the engine, causing rapid engine wear. This type of

damage is not covered under your Distributor’s Limited Warranty.

Inspection

See Figure 10 on page 3.

1. Press the latch tabs [1] on the top of the air cleaner cover [2], and

remove the cover.

2. Remove the foam element [3] from the air cleaner cover.

3. Remove the grid [4] from the paper element [5].

4. Check both elements to be sure they are clean and in good

condition.

5. Reinstall the grid over the paper element. Make sure that the grid

completely surrounds the paper pleats.

6. Reinstall the foam element in the air cleaner cover.

7. Set the paper element and screen grid in the air cleaner body, and

then install the air cleaner cover.

Cleaning

1. Tap the filter [5] several times on a hard surface to remove dirt, or

blow compressed air not exceeding 30 psi (207 kPa) through the

filter from the clean side that faces the engine. Never try to brush

off dirt. Brushing will force dirt into the fibers.

 WARNING

Gasoline is highly flammable and explosive, and you can be

burned or seriously injured when refueling.

• Stop engine and keep heat, sparks, and flame away.

• Refuel only outdoors.

• Wipe up spills immediately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GS190 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GS190

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info