Bedienungsanleitung Honda Honda Engines GX160 Regular (Seite 11 von 60) (Englisch)

13105

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

Cleaning

Dual-Filter-Element Types

Oil-Bath Type

GASKET

PRECLEANER CAP

AIR CLEANER

COVER

PAPER FILTER

ELEMENT

FOAM FILTER

ELEMENT

WING NUT

STANDARD DUAL-FILTER-

ELEMENT TYPE

WING NUT

AIR CLEANER COVER

WING NUT

PAPER FILTER ELEMENT

FOAM FILTER ELEMENT

CYCLONE HOUSING

GROOVE

AIR GUIDE

TAB

SPECIAL PAN SCREW (3)

CYCLONE DUAL-FILTER-ELEMENT TYPE

GRID

CAP

WING NUT

OIL LEVEL

AIR CLEANER

COVER

FILTER

ELEMENT

AIR

CLEANER

CASE

Remove the wing nut from

the air cleaner cover, and

remove the cover.

Remove the wing nut from

the air filter, and remove the

filter.

Remove the foam filter from

the paper filter.

Inspect both air filter

elements, and replace them if

they are damaged. Always

replace the paper air filter

element at the scheduled

interval (see page ).

Clean the air filter elements if they are to be reused.

Paper air filter element: Tap the filter element several times on a

hard surface to remove dirt, or blow compressed air [not

exceeding 207 kPa (2.1 kgf/cm

, 30 psi)] through the filter

element from the inside. Never try to brush off dirt; brushing will

force dirt into the fibers.

Foam air filter element: Clean in warm soapy water, rinse, and

allow to dry thoroughly. Or clean in nonflammable solvent and

allow to dry. Dip the filter element in clean engine oil, then

squeeze out all excess oil. The engine will smoke when started if

too much oil is left in the foam.

CYCLONE TYPE ONLY: Remove the three pan-head screws from

the precleaner cap, then remove the cyclone housing and air

guide. Wash the parts with water, dry them thoroughly, and

reassemble them.

Be sure to install the air guide as shown in the illustration.

Install the cyclone housing so the air intake tab fits into the

groove in the precleaner cap.

Wipe dirt from the inside of the air cleaner case and cover, using

a moist rag. Be careful to prevent dirt from entering the air duct

that leads to the carburetor.

Place the foam air filter element over the paper element, and

reinstall the assembled air filter. Be sure the gasket is in place

beneath the air filter. Tighten the air filter wing nut securely.

Install the air cleaner cover, and tighten the wing nut securely.

Remove the wing nut, and remove the air cleaner cap and cover.

Remove the air filter element from the cover. Wash the cover

and filter element in warm soapy water, rinse, and allow to dry

thoroughly. Or clean in nonflammable solvent and allow to dry.

Dip the filter element in clean engine oil, then squeeze out all

excess oil. The engine will smoke if too much oil is left in the

foam.

Empty the used oil from the air cleaner case, wash out any

accumulated dirt with nonflammable solvent, and dry the case.

Fill the air cleaner case to the OIL LEVEL mark with the same oil

that is recommended for the engine (see page ).

Oil capacity:

Reassemble the air cleaner, and tighten the wing nut securely.

60 cm

(2.0 US oz , 2.1 Imp oz)

05/06/17 17:25:32 32Z4F601_011

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GX160 Regular Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GX160 Regular

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info