Bedienungsanleitung Honda HRX537 HYEA (Seite 14 von 23) (Englisch)

580898

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

ENGLISH

Air Cleaner Service

A dirty air filter will restrict air flow to the carburetor, reducing engine

performance. If you operate the mower in very dusty areas, clean the

air filter more often than specified in the MAINTENANCE SCHEDULE

(page 13).

NOTICE

Operating the engine without an air filter, or with a damaged filter, will

allow dirt to enter the engine, causing rapid engine wear. This type of

damage is not covered by the warranty.

1. Press down on the

air cleaner cover [1]

tabs, and then

remove the cover.

2. Remove the filter [2]

from the air cleaner

housing [3].

3. Inspect the filter, and

replace it if it is

damaged.

4. Clean the filter by

tapping the filter

several times on a hard surface to remove dirt, or blow

compressed air (not exceeding 207 kPa) through the filter from the

inside. Never try to brush off dirt; brushing will force dirt into the

fibers.

5. Wipe dirt from the inside of the air cleaner housing and cover,

using a moist rag. Be careful to prevent dirt from entering the air

duct that leads to the carburetor.

6. Reinstall the filter and cover.

Spark Plug Service

NOTICE

Incorrect spark plugs can cause engine damage.

For good performance, the spark plug [1] must be properly gapped

and free of deposits.

1. Disconnect the spark plug cap [2],

and remove any dirt from around the

spark plug area.

2. Remove the spark plug with a spark

plug wrench [3].

3. Inspect the spark plug. Replace it

if the electrodes are worn or if the

insulator is cracked or chipped.

Clean the spark plug with a wire

brush if you are going to reuse it.

4. Measure the spark plug electrode

gap with a suitable gauge. The

gap should be 0.7 ~ 0.8 mm.

Correct the gap, if necessary, by

carefully bending the side

electrode.

5. Install the spark plug carefully, by

hand, to avoid cross-threading.

6. After the spark plug seats, tighten with a spark plug wrench to

compress the washer.

If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the

spark plug seats.

If installing a new spark plug, tighten 1/2 turn after the spark plug

seats to compress the washer [4].

NOTICE

A loose spark plug can overheat and damage the engine.

Overtightening the spark plug can damage the threads in the

cylinder head.

7. Install the spark plug cap on the spark plug.

Spark Arrester Service

The spark arrester must be serviced every 100 hours to keep it

functioning as designed.

1. Allow the engine to cool, then remove the three bolts [1] from the

muffler shield [2] using a 10 mm socket wrench.

2. Remove the muffler shield [2].

3. Remove the screw [4].

4. Remove the spark arrester [3] from the muffler [5].

5. Check for carbon deposits on the spark arrester and the exhaust

port. Brush carbon deposits away. Be careful to avoid damaging

the spark arrester screen.

6. Install the spark arrester in the muffler.

7. Install the muffler components on the engine, and tighten the three

bolts securely.

Recommended spark plugs: NGK - BPR5ES

[1]

[2]

[3]

[2]

[1]

[3]

0.7 ~ 0.8 mm

[4]

[5]

[4]

[2]

[3]

[1]

HYEHZE bk1.book Page 14 Monday, September 8, 2008 9:46 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda HRX537 HYEA Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda HRX537 HYEA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info