Bedienungsanleitung Honeywell DFS8MS (Seite 2 von 14) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

681060

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

- 2 -

DFS8MS – Installation instructions

Wireless smoke detector

English

Manually testing your smoke detector.

It is recommended the smoke detector be tested after installation, then at least once a

week to check the device is working properly. Press the "siren test/stop" button and

keep it pressed until an alarm is triggered and the red light starts flashing (see figure 4).

The siren will stop sounding once the button is released.

In the case of an interconnected configuration, when one of the DFS8MS detectors

enters test mode, all interconnected DFS8MS detectors also enter this mode.

WARNING 1: do not test with a flame. This may set the detector on fire and

damage your home. We recommend against testing with smoke because results

may be misleading, unless a special device is used.

WARNING 2: make sure you protect your ears during the test.

Test when installing detectors inter-connected by radio

1- Position the detectors at their planned installation site

2- Fold the antennae of each interconnected detector into two equal parts

3- Trigger a detector with the help of smoke or a smoke simulator, then check that once

the detector in question has activated its alarm function, all other interconnected

detectors also activate their alarm

4- Repeat this test for each inter-connected detector

5- Reposition the antennae in their initial position (unfolded)

The test is satisfactory if all attempts have led to the activation of the alarm of each

interconnected detector.

"Siren test/ stop" button to control your detectors

The DFS8MS detector is equipped with a "siren test/stop" button to help you control it.

• To cancel an alarm, press the test button. The alarm will remain silent for about 10

minutes. The red light on the hood of the smoke alarm will flash every 10 seconds to show

that the unit has been muted. If, after 10 minutes, the DFS8MS continues to detect

smoke, it will trigger the alarm again.

In an interconnected configuration when one DFS8MS is muted after detecting smoke, all

DFS8MS are also muted. Conversely, pressing a test button of a DFS8MS which has not

detected smoke will not mute any of the DFS8MS. The DFS8MS whose red light is

flashing rapidly is that which has detected smoke.

Replacing the product

This product is powered by a sealed lithium battery that does not need replacing over its

recommended 10 year life span.

1. As part of regular maintenance, you should always check the device's replacement date.

After this date, the device must be replaced.

2. If the device has not been replaced by the due date, its battery will run out, triggering an

audio signal every 40 seconds indicating replacement is required.

3. When you replace a device, make sure the old one is recycled. Correct disposal or

recycling will avoid any damage to the environment or human health. When you dispose

of the product, make sure you separate it from other waste to ensure it will be recycled

ecologically and healthily.

Note: prolonged exposure to low or high temperatures or an excessive humidity rate

may reduce the life span of batteries. The life span of batteries will also be reduced in

the case of prolonged warning cycles.

Upkeep

Regularly clean the smoke detector head. Use a soft brush or the brush accessory of your

vacuum cleaner to remove dust and spiders webs from side openings through which the

smoke enters. To clean the hood wipe it with a damp cloth then dry it carefully.

The smoke chamber of the detector head performs a self-test every 40 seconds. If it is in

damaged condition, an audio alarm will sound every 32 seconds. In this case, clean the

smoke detector head as indicated above. If the problem persists, return the device.

Smoke detectors, particularly optical types (photoelectrical) are susceptible to the

penetration of dust and insects, which can trigger false alarms.

The manufacture of this product was undertaken using the most up to date designs

materials and techniques. It is nevertheless impossible to avoid completely the effects of

contamination by dust and insects. To extend the life span of the detector, you must

therefore ensure it is kept clean and prevent the accumulation of dust. Insects or spiders

webs found near the smoke detector should be rapidly removed.

In certain circumstances, even regular cleaning may not be sufficient to prevent

contaminants from accumulating in the smoke detection chamber, and triggering the alarm.

If this occurs, the smoke detector must be returned. Contamination is beyond our control, is

totally unforeseeable and should be considered as normal wear and tear. This is why it is

not covered by guarantee. Work caused as a result will be invoiced.

WARNING: do not paint the detector.

Finally, the device must be replaced after 10 years of use (check the "replacement date"

indicated on the side of the device)

Features

Radio-frequency range

1,000 m on open land

Battery

Lithium, sealed and with a life span equal to that of

the product

Service voltage

3 V

Battery life span (type)

Product life span: 10 years

Frequency

Narrow band, 868 MHz

Operating temperature

from 0° to +40°C

Siren output power

85 dB(A) at 3 m

Supervision

Yes

Detection

Optical smoke alarm

getconnected.honeywell.com

Honeywell DFS8MS Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell DFS8MS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info