Bedienungsanleitung Honeywell HZ-420 Series (Seite 6 von 29) (Englisch, Französisch, Spanisch)

527101

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

We recommend that the 360º Ceramic Surround Heater be cleaned at least once a month and before

off-season storage.

• Turn the heater OFF (

) or ( ) and unplug it. Allow it to cool.

• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES,

POLISHES OR ANY CHEMICAL SOLUTION.

• Before storing, clean the 360º Ceramic Surround Heater using the above-mentioned steps. Wrap the

cord around the unit. Place in its original box and store it in a cool, dry place.

• This heater does not disassemble.

CLEANING AND STORAGE

SAFETY FEATURES

The 360º Ceramic Surround Heater is equipped with several devices and features for added protection:

• 360° SafetyTIP™ is an all-around tip-over switch that disables the heater if it is accidentally tipped

in any direction.

• A high temperature safety control prevents overheating.

• This heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater

should it operate at a higher than normal temperature.

• This heater was created using a high quality safety plastic.

• To set the thermostat, press the Temp Set button until Desired Temperature is reached. Note: the Desired

Temperature will flash three times and then Current Temperature in the room will display as a steady red.

• To constantly run the heater without a thermostat setting, press the Temp Set button until HI is

displayed in Temperature Display. In this mode, make sure to manually shut the heater OFF when

done using this appliance.

• To set the Timer, press the (

) button to select 1, 2, 4, or 8 hour setting. The heater will run for

that chosen period in the selected mode, counting down the remaining time in the display bar and

automatically shut off after the desired time has passed.

OPERATION (CONTINUED)

Remote Control

The Digital 360° Surround Heater can be completely controlled with the remote. Two AAA 1.5V batteries are

required (included). To install batteries:

• Remove the cover located on the back of the remote control.

• Insert two AAA 1.5V batteries, positioning them correctly (see instructions in the batteries compartment).

• Replace the cover.

Remote Control Operation

• Locate remote control packed in the top insert.

• Press (

) to turn heater on or off.

• Press (

) to choose LO (900W) or HI (1500W) Heat Level Setting.

• Press (

) to choose 1, 2, 4 or 8 hour setting.

• Press SET to choose a thermostat setting. Desired Temperature

will flash three times and then Current Temperature in the room

will display as a steady red.

• Replace remote control in the holder on the side of the heater

when not in use.

Model HZ-440 Remote

Power

Button

Heat

Level

Setting

Temperature

Set Button

Timer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HZ-420 Series Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info