Bedienungsanleitung Hoonved SP40E (Seite 15 von 21) (Englisch)

637629

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

ENGLISH

Part 1: General description and Safety devices

For the operator

2.1 WASHING PHASES C/SP E

2.1.a Switching on and Preparing the machine

To switch on the machine, press the power switch (Q1)

into the ON position.

The LED indicating the last cycle selected will become

CONSTANTLY LIT (LC1 or LC2 or LC1 and LC2), as will

the CHECK LED and the tank temperature LED (LTV).

IMPORTANT

On rst switching on, LED LC2 will light up.

The boiler, and then the tank, will start to ll automatically.

Once the water level has been reached, the heating

elements will switch in, rst in the boiler, then in the tank.

Once the water in the tank reaches the correct tempera-

ture, the tank temperature LED (LTV) will go ON.

WASHING OPERATION

If not equipped with an automatic dosing system, pour

into the tank a quantity of detergent suitable for the volu

me and hardness of the water. For quantities, refer to the

specic instructions for the detergent in use.

ATTENTION

When items to be washed are encrusted with burnt

on matter, or a long time has passed between use

and washing, it is essential to carry out a pre-was

soak using a suitable softening agent.

The use of hand-washing products is to be avoided

as they could produce foam inside the machine.

IPlace the basket of items to be washed inside the machine,

having rst removed any solid waste.

2.1.b Selecting a Cycle

The duration of the washing cycle can be chosen from

three different lengths of time (SHORT, MEDIUM, LONG),

to be selected using the “CYCLE (S9)” button.

Each time the “CYCLE (S9)” button is pressed, the blue

LEDs

LC1 or LC2 or LC1 and LC2 together.

CHECK

2.1.c STARTING THE WASHING CYCLE

To start the washing cycle, press and hold the START (S3)

button for a few seconds, then release.

Throughout the washing cycle the LED(s) for the selected

cycle (LC1 or LC2 or LC1 and LC2 together) will FLASH.

ATTENTION

We recommend that you top up the detergent used up

by washing grease or dispersed during rinsing every 4-5

complete cycles.

The use of the machine ensures rinsing at the ideal tem-

perature for hygienic purposes every time;

Indeed, if the temperature is not sufcient the wash will

be automatically prolonged so as to ensure the necessary

conditions of optimum rinsing at 85°C.

The waiting time required to attain optimum temperature

can extend to a maximum of 8 minutes.

While this is taking place, the CHECK LED will FLASH

RAPIDLY until the end of the cycle. To reset the ashing,

switch the machine off and back on using the power

switch (Q1) .

2.1.d Interrupting the cycle

1) It is possible to interrupt the washing cycle momentarily

by opening the door, this is an EMERGENCY measure:

the cycle LEDs (

LC1 or LC2 or LC1 and LC2 together)

will start to FLASH, alternating with the CHECK LED.

On closing the door, operations will resume from the point

in which they stopped.

2) The cycle can also be interrupted by SWITCHING the

machine’s power switch (Q1) to the OFF position.

3) On switching the machine back on, the LED indicating

the last cycle selected will light up.

At the end of the washing cycle, take out the basket

and shake it gently so as to remove the last drops

left on the washed items.

Allow items to dry and remove them from the basket with

clean hands.

Store all items on hygienic and completely stable surfaces.

2.1.e Manual Draining

It is possible to drain the water from the tank at any time

during the day, according to the waste accumulated.

To carry out this operation, proceed as follows:

- Switch the machine’s power switch (Q1) to the OFF

position and release the overow, allowing all the water

to drain from the tank;

- Remove the tank lters (22/23) and clean;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoonved SP40E Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hoonved SP40E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info