Bedienungsanleitung Hoonved SP40E (Seite 17 von 21) (Englisch)

637629

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

ENGLISH

For the operator

2.2 CLEANING (Fig. 10)

2.2.a General information

Strict compliance with the maintenance instructions in this

section will keep your machine in a good working condition

and will notably reduce the need for repairs.

ATTENTION

If any machine component becomes faulty, FIRST CHECK

that all the instructions given in the previous paragraphs

have been complied with during use.

Repairs must be carried out immediately, as soon as the

fault occurs. This will prevent the trouble from becoming

worse and damaging other parts.

ATTENTION

It is forbidden to clean the machine with water jets.

ATTENTION

Daily operations to carry out when work has ended, with

the machine OFF , the main circuit-breaker disconnected,

the water cocks off and the washing tub empty.

1. Thoroughly clean the inside parts of the machine.

2. Remove the lter (22) from the bottom of the machine

by releasing the overow (21).

3. Remove the suction protection (23).

4. Wash the lters under running water and t them cor-

rectly back in their housings.

ATTENTION

Frequently check and clean the spraying units, removing

them from their housings and eliminating any dirt and

fouling. The frequency with which this operation must be

carried out depends on the quantity of dirt or on the unsa-

tisfactory washing results. Never use corrosive products

like sodium hypochlorite (bleach) or hydrochloric acid, wire

wool or steel brushes to clean either the inside or outside

parts of the machine.

2.3. PREVENTION MAINTENANCE (Fig. 10)

The preventive maintenance operations must be carried

out with the machine OFF, the main circuit-breaker di-

sconnected, the water delivery cocks off and the washing

tub empty.

2.3.a Checking and cleaning the spray arms and

nozzles (Fig. 10)

Periodically check to make sure that the lower washing

arm and rinsing arm (24/25) and their relative nozzles are

not clogged (26/27).

Cleaning the lower/upper unit

1. Unscrew the ring nut and lift the arm (24/25).

2. Wash the washing and rinsing arm.

If the nozzles (27) are clogged, unscrew them to de-

mount and clean, taking care to prevent the shape of

the nozzle from being deformed. After cleaning, t the

nozzles exactly back in their original positions.

3. Remount all parts by complying with the above instruc-

tions in reverse.

2.4 DESCALING

Where hard water is present lime scale deposits will for

in the machine and on dishes, which must, for reasons

of hygiene, be removed by descaling.

Advice on operation procedures and frequency for this

treatment are generally given by the detergent supplier,

who can provide suitable products.

In order to avoid damaging the machine, do not

exceed recommended doses, follow the detergent

producer’s directions scrupulously and, having

nished operations, rinse thoroughly.

2.5 TEMPORARY STOPPAGE

If the machine is to be left inactive for a period of some

weeks, it is advisable beforehand to load the tank and

run a few empty cycles with clean water then drain, so

as to avoid the formation of unpleasant odours.

If necessary, repeat the process several times until the

water is still clean after washing.

If the stoppage is to be very long, it is advisable to

drain the water from the boiler and from the electric

pump.

2.6 DEMOLITION and DISPOSAL

When the machine is to be scrapped, drain the water

from the tank and from the boiler, as indicated in the

points above, and disconnect the machine from the wa-

ter

and electricity supply networks, then dispose of the

components according to current regulations, respect-

ing

national and local ecological and environmental

legislation, and taking care to separate the parts as

follows:

- metallic parts: body work, surfaces, panels, lters;

- electrical parts: motors, remote switches, micro-

switches, cabling;

- plastic parts: connectors, baskets;

- rubber parts: tubes, couplings

2.7 SCHEDULED MAINTENANCE

It is advisable to subject the machine to scheduled

maintenance every 6 months.

The producer declines all responsibility for any

printing errors contained in this booklet.

The instructions, drawings, tables and everything else

in this manual are of a condential technical nature.

For this reason, none of the information may be either

completely or partially duplicated or disclosed to

third parties without prior written authorization from

HOONVED which is the sole proprietor and which

reserves the right to make any modications as may

be considered necessary without advance warning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoonved SP40E Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hoonved SP40E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info