Bedienungsanleitung Hoover MaxExtract Deep Cleaner (Seite 10 von 60) (Englisch, Französisch, Spanisch)

594429

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Actual model may vary from images shown.

3.1/3.1a

CLEANING CARPET

Read “Before You Begin Cleaning” instructions.

Fill Clean Water Tank according to instructions

for Fig. 2.9.

Fill detergent container with Hoover

detergent

according to instructions for Fig. 2.10.

Select proper SpinScrub

mode (Fig. 2.6).

Dry hands and plug cord into a properly

grounded outlet.

IMPORTANT

To assure proper rinsing, it is important to keep

the cleaner on the same path backward as

forward.

8&5

%3:

3.2

IMPORTANT

To avoid saturating carpet, do not use more

than 4 wet strokes over one area. Always end

with dry strokes.

Release trigger and slowly push cleaner forward

over area just sprayed with solution (dry stroke).

Then slowly pull cleaner back toward you without

squeezing trigger (dry stroke). Continue using dry

strokes until little water is visible passing through

FOR MODELS WITH AUTO RINSE FEATURE

(available on select models only)

3.1a Set Wash/Rinse Setting switch to Wash/

Auto Rinse. Turn cleaner ON.

3.2a Squeeze trigger to apply cleaning

solution and slowly push cleaner forward

(equals one wet stroke). The cleaner washes

on the forward stroke.

Continue to squeeze trigger and slowly pull

cleaner back toward you (second wet stroke).

The cleaner rinses the carpet on the

backward pass.

3.3

3.2a

AUTO

RINSE WASH

FOR MODELS WITHOUT AUTO RINSE

FEATURE

3.1 Set Wash/Rinse Setting switch to Wash.

Turn cleaner ON.

3.2 Squeeze trigger to apply cleaning solution

and slowly push cleaner forward (equals one

wet stroke).

Continue to squeeze trigger and slowly pull

cleaner back toward you (second wet stroke).

Step 1

the Dirty Water Tank lid (Pass over the same area a

minimum of 4 times = 2 while squeezing the trigger

and 2 without).

For best results, use straight, parallel strokes.

Overlap strokes by 1 inch to help prevent

streaking.

Keep nozzle flat on floor for both forward and

reverse strokes.

3.3 If you would like to rinse the carpet with water

only, set Wash/Rinse Setting switch to RINSE.

Repeat cleaning motion. In this setting, rinsing will

be done on both forward and reverse strokes.

For heavily soiled areas, repeat cleaning motion.

Avoid saturating carpet.

It is best to alternate wet and dry strokes as

described above.

For best cleaning results and to aid in faster drying

of carpet, end with more dry strokes. (Continue

using dry strokes until little water is visible passing

through the Dirty Water Tank lid.)

Empty Dirty Water Tank when the motor sound

becomes higher pitched and there is a loss in

suction (see “Automatic shut-off”, Fig. 2.19).

When finished cleaning, follow “After Cleaning”

instructions on page 12.

Step 2

IMPORTANT

Do not clean over floor electrical outlets.

To avoid walking on damp carpet, start at the end of

the room farthest from the door or path to sink

where tanks will be emptied and filled.

Step on handle release pedal and lower handle to

operating position.

Pull Trigger = WET

Release Trigger = DRY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover MaxExtract Deep Cleaner Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info